Congestion phone and restart LIM

[dnlazarev]

Urgently need help.
Maybe someone is encountered.
MD110 BC12 two Limni.
On March 8 began to hang. Hang all digital phones.
And the station goes into overdrive.
Throw out such errors.
<Allop; ALARM LOG
IDENTITY: ATS
VERSION: CXP1010139 / 2 / BC12SP6 / R3B
 
DATE: 08MAR15 TIME: 14:53:36
CLASS: 3
106 FAULTY I / O BOARD OR CONNECTED I / O DEVICE
DATE TIME ALP NOIF EQU BRDID INF1
08MAR15 11:42:40 January 18 001-0-60-03 106 3
 
CLASS: 2
274 DIGITAL TRUNK, CLOCK MALFUNCTION (SLIP)
DATE TIME ALP NOIF UNIT EQU BRDID INF1
06MAR15 15:36:56 May 1 SLP60 001-2-00-00 57265
 
CLASS: 1
10 CONTROL SYSTEM DISTURBANCE COUNTER AT TOP
DATE TIME ALP NOIF EQU INF1
08MAR15 11:40:11 January 13 001-0 - ** - ** 0
 
73 LIM RESTARTED
DATE TIME ALP NOIF UNIT EQU INF1
08MAR15 11:41:03 January 15 RER 001-0 - ** - ** 2
 
CLASS: 0
There is a lot of mistakes on flows.
ALREI NOT DONE!
 
Then it happened again on March 16.
19th Reload station completely on nutrition.
22 was repeated again the same thing.
C removed today morning Voice server c 001-0-60-03.
DATE: 08MAR15 TIME: 14:53:36
CLASS: 3
106 FAULTY I / O BOARD OR CONNECTED I / O DEVICE
DATE TIME ALP NOIF EQU BRDID INF1
08MAR15 11:42:40 January 18 001-0-60-03 106 3
 
And today again stuck, but the station is not a thing of the restart.
Manifested in the following way - shoot digicam on the phone and thus the display Congestion
When you call the machine the call goes through, but after lifting the handset silence.
Through 3-5 minutes to restore everything, and there are no errors.
Attached is a listing at the time of freezing.

 

[himdp]

Hi,
I am sure people will point out to you that the system software you have is very old and the recommendation is to upgrade.
You do not even have all the service packs available for BC12 installed.

The problem you have is the LIM is restarting due to too many lost signals in a short time.

Go to this link -

https://onedrive.live.com/?id=5FC098E631EDE075!114&cid=5fc098e631ede075

Look at the document 022-03 MD110 Software Slides where there is a section on Lost Signals and LIM restarts.

To determine the cause you should print the HIMDP after the restart. It is possible that the cause of your problem is hardware which can be replaced, but it is most likely to be software in which case you will have trouble obtaining a solution.

HIMDP might be lost if the LIM has reloaded or the signals causing the problem night have been overwritten, a more reliable diagnostic is the SYAR print, but this needs in depth knowledge to analyse and must be reset before the event as it will never be overwritten and might contain an information.

See the 'System Area' section of the document for an overview of SYAR.

Please try to refrain from manually restarting programs such as ELP6 and KLP1T as the LIM restart will have already performed that nad you will only be increasing the time for the system to stabilize.

Good luck.

 

[dnlazarev]

Thanku.
Looked just dump preserved.
Decrypt it. But because of what was a reboot did not understand.
EX22MAR.res decrypted file