Configuring Trunks (PRI, TIE, DISA, T1, COT) for CS 1000 5

[Wash1]

Everyone I've worked on meridians, but every job I go to everything is configured so I do the MACS. I've been tasked to configure trunks mainly PRI and DISA for the CS 1000. Can some one give me a elementary break down on how to do this. I know you use multiple loads, but can yall help me please with the step by step actions? Please please please

 

[Wash1]

Im' getting somewhere. Here are the steps I performed

1. LD 60 disl 13
2. Ld 16 outted the RDB
3. LD 14 outted the trks
4. LD 17 finally got the DCH 23 outted
5. Ld 17 chg cequ at the DLOP prompt i used X13 which worked.

Now when I prt cequ pri 13 isn't there good.

When go to LD 60 stat 13 the loop is there how do I delete this loop? What step am i missing?

 

[DocVic]

So, here it is 33 days later. How much do they pay you per hour? How many hours have you wasted trying to get this PRI working? How long would it have taken you to call a tech, have him come in and get it working, while you look over his shoulder and he teaches you to do this, and you make notes??? I'm sure everyone here would not stop helping you, but there comes a time when we can recognize when someone needs some on-site help. Sometimes "hand holding" doesn't work with newbees. This is one of those cases. Make the call before your bosses realize how much time you have wasted. 33 days!
When your done, read all the docs for this machine and play with it. Just don't break it. Aspire to help others learning, like we do.

DocVic
Dedicated to Nortel Products till the end.
Need help?

http://www.TSS-CO.com

 

[Wash1]

LOL I have had a hard lesson the the last several weeks. Guys thanks so far for your help. If I could call the vendor in I would, but at this time I can't. I so amazed of what I have learned so for, but I missing a step. Please help. When I go to LD 60 Stat 13 how do I out that loop I done all of the other steps what am I missing?

 

[Reusser]

when you stat 13 - what do you see?

All channels must be removed including Dchannel.LD 14 and 17
Loop must be disabled. LD 60
No assignment to Clock. LD 73
if TMDI card - card must be disabled. LD 96

once that all done,
LD 17
req: chg
Type: cequ
DLOP: x13

 

[Wash1]

Here are the steps I performed

1. LD 60 disl 13
2. Ld 16 outted the RDB
3. LD 14 outted the trks
4. LD 17 finally got the DCH 23 outted
5. Ld 17 chg cequ at the DLOP prompt i used X13 which worked.

Now when I prt cequ LD 22 pri 13 isn't there good.

When go to LD 60 stat 13 the loop is there how do I delete this loop? What step am i missing?

HELP this switch is constanly INI / Restarting help please.

>ld 60
DTI000
.stat 13

DTI TRK LOOP 13 - ENBL
FFMT/LCMT/YALMT: AMI/DG2
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : WAITING
CH 01 - UNEQ CH 02 - UNEQ
CH 03 - UNEQ CH 04 - UNEQ
CH 05 - UNEQ CH 06 - UNEQ
CH 07 - UNEQ CH 08 - UNEQ
CH 09 - UNEQ CH 10 - UNEQ
CH 11 - UNEQ CH 12 - UNEQ
CH 13 - UNEQ CH 14 - UNEQ
CH 15 - UNEQ CH 16 - UNEQ
CH 17 - UNEQ CH 18 - UNEQ
CH 19 - UNEQ CH 20 - UNEQ
CH 21 - UNEQ CH 22 - UNEQ
CH 23 - UNEQ CH 24 - UNEQ


I went to ld 60 disl 13 and this what I got before it INI / restarted.

disl 13

OK
.
BUG302 TNTRANS was called with an illegal value, TN FFFFFFFF

BUG302 TNTRANS was called with an illegal value, TN FFFFFFFF

BUG302 TNTRANS was called with an illegal value, TN FFFFFFFF

THE SWITCH IS CONSTNTLY INI / RESTARTING HELP

 

[marcuspb]

Call a vendor now 1-877-877-2269 (this is just the first one that I came up with, not promoting one over another)

 

[Wash1]

It would take an act of congress to get someone here. Is there any other suggestions at this time? It has to be something small. I want to ou loop 13 that I see in load 60 and there's a TMDI card in the CS1000E located at 0 1 3 how do I out that card and reinstall it. Please help Thanks everyone?

 

[DocVic]

We have all tried, but, you really don't know how to take advise, do you!? You're in a pickle! The ship is burning (INIT/RELOADING) and is gonna sink soon, and you say "it would take an act of congress"? I'm betting you say that cuz the company your work for is just too cheap, right!? You might want to take a couple of your bucks and pay for that tech yourself, cuz they are going to FIRE YOU! Good luck!

DocVic
Dedicated to Nortel Products till the end.
Need help?

http://www.TSS-CO.com

 

[Wash1]

Thanks everyone.