configure remote modem? AT commands.

[hughiepal]

Hi, does anyone know how to configure a modem at the remote end ie that it answers and connects to the Md110.
How do I clear the AT commands already stored in it.
What commands should I put in it and how do I store these commands so that even if the modem is powered down, they will remain stored.
The modem is normal 56K US robotics.
Cheers

 

[lalrl]

1. ats0=1 (autoanswer after one ringtone)
2. atq1 (supress ok-answer)
3. ate0 (supress echo)
from now youm must enter the next commands blind:
4. at&d (enter blind!)
5. at&y0 (loading register 0 after powerdown or reset
6. at&w0 (write and store to register 0)
if programming fails, enter blind:
7. at&f (set to fabric, delivery-state)
start from 1.

absolutely reliable...

 

[harddisk15]

Thanks Lairl, Believe me - not a lot of people new this.
Cheers

 

[harddisk15]

Hi, I still have a problem. The md accepts the SSSSSSS'S but does not come back with 'ENTER PASSWORD'. I've pasted on +++ AT&V. Any ideas?


ATDT123456
CONNECT 1200 V42bis
+++SSSSSSSSSSSSSSSSSSSSS;
OK
AT&V

Option Selection AT Cmd
--------------- ------------ --------
Comm Standard CCITT B
CommandCharEcho Enabled E
Speaker Volume High L
Speaker Control OnUntilCarrier M
Result Codes Enabled Q
Dialer Type Tone T/P
ResultCode Form Text V
ExtendResultCode Enabled X
DialTone Detect Disabled X
BusyTone Detect Enabled X
LSD Action Standard RS232 &C
DTR Action Standard RS232 &D
Press any key to continue; ESC to quit.

Option Selection AT Cmd
--------------- ------------ --------
V22b Guard Tone 1800 Hz &G
Flow Control Hardware &K
Error Control Mode V42,MNP,Buffer \N
Data Compression V42bis/MNP5 %C
AutoAnswerRing# 0 S0
AT Escape Char 43 S2
CarriageReturn Char 13 S3
Linefeed Char 10 S4
Backspace Char 8 S5
Blind Dial Pause 4 sec S6
NoAnswer Timeout 60 sec S7
"," Pause Time 2 sec S8
Press any key to continue; ESC to quit.

Option Selection AT Cmd
--------------- ------------ --------
No Carrier Disc 2000 msec S10
DTMF Dial Speed 90 msec S11
Escape GuardTime 1000 msec S12
Data Calling Tone Enabled S35
Line Rate 33600 S37
Press any key to continue; ESC to quit.

Stored Phone Numbers
--------------------
&Z0=
&Z1=
&Z2=
&Z3=

OK
AT
OK

 

[rfpui]

If you press +++ it is a signal for your modem that the command is send to modem but not to external device (MD 110)
after +++ You can program modem not MD

If you want to connect to MD send
SSSSSSSSSS;
without +++

 

[harddisk15]

Hi RFPUI, I only did the +++, AT&V to show you guys how my modem is configured. After sending my capital SSSSSSSSSS's
the cursor goes back to the start of the line and I'm not asked to enter the password.

 

[harddisk15]

Hi RFPUI, After the SSSSSSSSSSSSSS's are entered t5he cursor goes back to the start of the line and I'm not asked to enter the password. I only pressed +++ AT&V to show you guys how my modem is configured.
Cheers

 

[rfpui]

Try to restart IPU or NIU board,
The best way is swich off HDU, unplug IPU/NIU board wait ca 10 sek. and plug it again, swich on HDU.

 

[hughiepal]

Hi rfpui, I've tried that, there is a Tracker modem working ok on the same board -- I've restarted the board, pulled it - there is a tracker modem on the same board which works fine. Don't ask - due to political reasons the company needing access are not allowed to use the tracker.
The answer must be in the modem setup. (I think)

 

[patcher]

Hello hughiepal, I really don't know what is your problem. If you like to change the modem settings, you had to connect your rs232 directly to the modem you are trying to configure. There is no way to change the settings of the remote modem via carrier signal. If you +++ while you are connected to will just change your modem and not the remote modem. To go back after +++ is ATO. /patcher

 

[harddisk15]

Hi, I wasn't trying to change the settings - just display what the they were.
cheers

 

[DUFQI]

check your speed parameters modem-modem and RS232-MD.
Should be fix with e.g. 9600

 

[tigerlow66]

Hi,

Had encountered the same problem as follow :

case 1 : after issued SSSSSSS; but the MD did not responsed with SSSSS via the remote modem.
1.1 Action taken : restarted IPU OK,but for a short period of time only, after that same problem happed again.

case 2 : under case 1 condition , some other PC or Notebook with modem had successfully connected to MD without any problem.

Question : is this a common symptom for using IPU card.any patch on MD that can help to improve this situration.

Any info is welcomed.

Many thanks