glamprecht1
IS-IT--Management
this quest to configure this Cat 2948G-GE-TX has evloved from not understanding the privliged exec mode (previous post) to now nearing a more complete config. Can anyone look at this to see if i am missing anything.
It all seems to work but in my humble opinon and experience, thats not saying much!!
All of my other IOS switched will have span tree enabled and will look like this in the config
...............................................
spanning-tree mode pvst
no spanning-tree optimize bpdu transmission
spanning-tree extend system-id
!
!
interface FastEthernet0/1
spanning-tree portfast
.................................................
Here is the 2948 non default config...
# ***** NON-DEFAULT CONFIGURATION *****ntree portinstancepri 2/5 0 mst
!
!
#time: Tue May 22 2007, 08:49:11antree portinstancepri 2/6 0 ms
!
#version 8.3(2)GLXe sl0 down
!e
!s
#system web interface version(s)tnnected 100 32 disabled
set password $2$mjvg$sJO7ifuSd.Ik4DXPtIMZb. mst
set ip rout
2/24
set enablepass $2$wwA7$njdv4D5nwXZSO0hsosI2W/sabled 0
set ip alias de
set spantre
!p
#dot1xancepr
set feature dot1x-radius-keepalive disable not-
set spantree portinstancepri 2/11
!
#frame distribution methodip dns server 1
set ip route 0.0.0.0/0.0.0.0 10.1.1.3
set ip alias default 0.0.0.0
!
#dns
set ip dns server 10.1.3.4 primary
set ip dns server 10.1.3.5
set ip dns enable
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat4000-k8.8-3-2-GLX.bin
!
#http configuration
set ip http server enable
!
#multicast filter
set igmp filter disable
!
#module 1 : 0-port Switching Supervisor
!
#module 2 : 52-port 10/100/1000 Ethernet
end
Console> (enable)
Is this enough info to go off of or do i need to post more?
Just want to make sure that this swtitch is configured to behave with my others.
Thanks!!!
It all seems to work but in my humble opinon and experience, thats not saying much!!
All of my other IOS switched will have span tree enabled and will look like this in the config
...............................................
spanning-tree mode pvst
no spanning-tree optimize bpdu transmission
spanning-tree extend system-id
!
!
interface FastEthernet0/1
spanning-tree portfast
.................................................
Here is the 2948 non default config...
# ***** NON-DEFAULT CONFIGURATION *****ntree portinstancepri 2/5 0 mst
!
!
#time: Tue May 22 2007, 08:49:11antree portinstancepri 2/6 0 ms
!
#version 8.3(2)GLXe sl0 down
!e
!s
#system web interface version(s)tnnected 100 32 disabled
set password $2$mjvg$sJO7ifuSd.Ik4DXPtIMZb. mst
set ip rout
2/24
set enablepass $2$wwA7$njdv4D5nwXZSO0hsosI2W/sabled 0
set ip alias de
set spantre
!p
#dot1xancepr
set feature dot1x-radius-keepalive disable not-
set spantree portinstancepri 2/11
!
#frame distribution methodip dns server 1
set ip route 0.0.0.0/0.0.0.0 10.1.1.3
set ip alias default 0.0.0.0
!
#dns
set ip dns server 10.1.3.4 primary
set ip dns server 10.1.3.5
set ip dns enable
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat4000-k8.8-3-2-GLX.bin
!
#http configuration
set ip http server enable
!
#multicast filter
set igmp filter disable
!
#module 1 : 0-port Switching Supervisor
!
#module 2 : 52-port 10/100/1000 Ethernet
end
Console> (enable)
Is this enough info to go off of or do i need to post more?
Just want to make sure that this swtitch is configured to behave with my others.
Thanks!!!