CLOCKALARM CCAFAULT

[ALGISV]

I have 2 lims in system connected with GS. GS give alarms. Client told that it is impossible make modem connections. Connentions have disconnected becouse of sincronization problems.
Config:
GJLII:EQU=1-0-00-0,CHL=32,GSMULT=0-0;
GJLII:EQU=1-1-00-0,CHL=32,GSMULT=0-2;
GJLII:EQU=2-0-00-0,CHL=32,GSMULT=0-4;
GJLII:EQU=2-1-00-0,CHL=32,GSMULT=0-6;
GSCNI:GSM=0;
GSDUI:GSSIDE=0,DUP=SINGLE;

SCICI:MCCL=0-0,RCCL=0-4;
GJLCP:LIM=1;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
1-1-00-0 0-2 1
1-0-00-0 0-0 1

END

<GJLSP:GSMULT=0-0&&7-30;
GROUP JUNCTOR LINE STATUS
EQU = 1-0-00-0 GS-MULT 0-0 MCCL
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING MASTER LINK
SIDE 0 ALARM 0000 0000 0100 0000


EQU = 1-1-00-0 GS-MULT 0-2
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0100 0000


EQU = 2-0-00-0 GS-MULT 0-4 RCCL
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING CLOCK CONTROL
SYNC RECEIVING
SIDE 0 ALARM 0000 0000 0100 0000


EQU = 2-1-00-0 GS-MULT 0-6
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0100 0000
Town conneciton sincronization:
<SCEXP;
EXTERNAL SYNC RECEIVING LINES DATA
MASTER LIM STATUS
FIRST CHOICE 1-1-20-0 SYNC RECEIVING
SECOND CHOICE NOT PRESENT
THIRD CHOICE NOT PRESENT

2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:51:43
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:51:48
2-0-00 0-04 0 LSIGJCG LOSS OF SIGNAL TO 0-08 14:51:49
NEGATIVE RECEIPT ON
SIGNALLING CHANNEL REQUEST
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:51:54
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:51:59
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:52:05
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:52:11
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:52:16
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:52:22
2-0-00 0-04 0 LSIGJCG LOSS OF SIGNAL TO 0-08 14:52:23
NEGATIVE RECEIPT ON
SIGNALLING CHANNEL REQUEST
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:52:27
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:52:33
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:52:38
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:52:44
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:52:50
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:52:55
2-0-00 0-04 0 LSIGJCG LOSS OF SIGNAL TO 0-08 14:52:56
NEGATIVE RECEIPT ON
SIGNALLING CHANNEL REQUEST
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:53:01
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:53:06
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:53:12
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:53:17
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:53:23
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:53:28
2-0-00 0-04 0 LSIGJCG LOSS OF SIGNAL TO 0-08 14:53:29
NEGATIVE RECEIPT ON
SIGNALLING CHANNEL REQUEST
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:53:34
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:53:39
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:53:44
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:53:50
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:53:55
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:54:01
2-0-00 0-04 0 LSIGJCG LOSS OF SIGNAL TO 0-08 14:54:02
NEGATIVE RECEIPT ON
SIGNALLING CHANNEL REQUEST
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:54:06
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:54:12
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:54:17
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:54:23
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:54:28
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:54:34
2-0-00 0-04 0 LSIGJCG LOSS OF SIGNAL TO 0-08 14:54:35
NEGATIVE RECEIPT ON
SIGNALLING CHANNEL REQUEST
2-0-00 0-04 0 CLOCKALARM CCAFAULT 14:54:39
2-1-00 0-06 0 CLOCKALARM CCAFAULT 14:54:45
Sombody can help to clear situation. That can be a problem?

 

[dstrang1]

Try blocking and then physically disconnecting GSMULT=0-4 from the G-board. Wait a few minutes for things to settle down and see if the problems have cleared. If not, de-block 0-4 and do the same with 0-6.

Do you have any other problems involving LIM-2? Faulty signals, synch errors etc?

Are all LED's and displays in the GS showing normal conditions?

Have you run a function test on the GSM? (GSFTI:GSM=X,test=board

Did this condition coincide with a recent hardware or configuration change? Why is 0-4 trying to signal 0-8 when it appears that 0-8 doesn't exist?

If none of these questions get you going in the right direction, come back & I'll think of some more.

Good luck,

Dave Strang

 

[trrep]

hi,

you hav a 2 lim system. the MD110 is using 3 LIMS as master normaly.
if you don't program al 3 lims as master ( scici) you will got always this "alarm bits" in the GJLSP printout.
normaly this causes no alarm in the Alarm protokol
(allop)!!

in a 2 lim system you are not able to set the ACCl .
so you can't fix your GJLSP printout.
normal answer: not a fault, it's a feature.

best regards