CLID on IFC D100

[philcap]

Hi

How could I put a default CLID in a PRI, D100 IFC. When an analog line (500 type) make a call over this PRI route their 4 digit line number was send instead a default CLID.

Below is my config.

****************************
ADAN DCH 15
CTYP MSDL
CARD 01
PORT 1
DES plexus
USR PRI
DCHL 1
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID 36
RCAP ND2 TAT
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7
****************************
TYPE RDB
CUST 00
DMOD
ROUT 15
DES
TKTP COT
PRIV NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO


PAGE 018

DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
ISAR NO
IEC ???
DAPC NO
BCOT 0
DSEL 3VCE
PTYP PRI
AUTO YES
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7888
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096
TFD 0
LEXT 100
DRNG NO
CDR NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO
********************
EQ:
AMLM024 05
prt

TYPE: cli

TYPE CLID
CUST


SCH0856

CUST 0

SIZE 256
RNGE


INTL

ENTRY 0
HNTN 416
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 8650200
DIDN NO
HLOC
LSC
CLASS_FMT DN

ENTRY 1
HNTN 416
ESA_HLCL
ESA_INHN NO
ESA_APDN NO
HLCL 8650200
DIDN NO
HLOC
LSC
CLASS_FMT DN

ENTRY 3
HNTN 416
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 369
DIDN YES
HLOC
LSC
CLASS_FMT DN

THANKS

 

[philcap]

Bye the way here is the net_data config...I forgot to include.

REQ PRT
TYPE: net

TYPE NET_DATA
CUST 0


TYPE NET_DATA
CUST 00
OPT RTD
AC2
FNP YES
ISDN YES
PNI 3705
PINX_DN
MBG 0
BSGC 65535
PFX1
PFX2
HLOC
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
TRNX NO
EXTT NO
FTOP FRES
VNR YES
RLI 12
CDPL 10
LOCL 10
NIT 8
FOPT 14

REQ:

 

[acewarlock]

Prt the TNB of the 500 set.

 

[johnpoole]

dn xxxx 1 should send

ENTRY 1 
  HNTN 416
  ESA_HLCL 
  ESA_INHN NO
  ESA_APDN NO
  HLCL 8650200
  DIDN NO
  HLOC 
  LSC  
  CLASS_FMT DN

if the 416 number is the number you are trying to send. is it all your analogs? and why is entry 0 and entry 1 the same? what table does your digitals send? all did's entry 3? if so change one of then to entry 1 or 0, the duplicate entry is a problem, i would delete one of them.. sometimes a small owersite in software can cause a problem thats hard to find

john poole
bellsouth business
columbia,sc