CLID is showing up differently on local calls vs LD calls 2

[atascoman]

Hello,

CS1000 R5.0. A phone using CLID table O is supposed to send out the main number for the campus. I checked the CLID table and it is setup properly. DIDN is set to NO etc. When they call me which is a LD call it shows up correctly, when they make a local call it send their extension as the CLID. Sounds like a translation issue, but I have never seen this before. Usually it's all or nothing with CLID stuff.

 

[phonz1]

the Telco attaches CLID info to the call. I would ask them what the issue is. Sounds as if your local Telco is wrong.

 

[atascoman]

Wel... As Expected I am being told the CO sends what it gets so I need to figure out how they are getting the extension for CLID instead of what is programmed on the CLID table. Is there another place to manipulate CLID other than the CLID tables in LD 15?

 

[Splic3d]

Post the RDB for the local route, if nds is in the RCAP it will seen more info than what the CO needs.

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx

 

[atascoman]

I turned off NDS on the DCH, no change. Here is the RDB.
REQ: prt
TYPE: rdb
CUST 0
ROUT 0

TYPE RDB
CUST 00
ROUT 0
DES LOCAL_PRI
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8197
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70


PAGE 002

ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 15
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO

 

[Splic3d]

Turn on MSGI and MSGO for the D channel of the local route and see what is being sent to the Telco. Use LD 96 for this. Enl Mon TTY, Enl msgi Dch#, enl msgo Dch#. Diala local call, it will print out info that is being sent to the telco.

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx