Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

CLID from Cisco CCM thru Nortel 81C to PSTN?

Status
Not open for further replies.

Telco01

Technical User
Jan 11, 2006
121
US
Can I get the called party to see the DID number of the Cisco phone connected to the Nortel 81C with a PRI connected to the outside world via PRI? We want to display the DID # of each Cisco phone or a pre-determined number set for the Cisco Phone profile in CCM.
 
Are you using QSIG on the PRI ?
I have the same setup, and the Cisco CLID goes out fine
 
This is what we have:

ADAN DCH 34
CTYP MSDL
GRP 1
DNUM 4
PORT 0
DES Cisco
USR PRI
DCHL 34
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
CTR2 2 3
PR_RTN NO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7



TYPE RDB
CUST 00
ROUT 5
DES CISCO
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
MBXR NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 1005
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 5888
NRD 5888
DDL 70
ODT 3328
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 4
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


DES TO CISCO SERVER
TN 034 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 3
RTMB 5 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS CTD DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE NO DATE


 
Okay, with the exception of the OVLR in the DCH, we are both programmed the same way on the Nortel side. When we first set up our integration, Cisco CLIDs were not going out. I had to go into CM Admin > Call Routing > Route/Hunt > Route Pattern.
Then I clicked on each of the Patterns that handle outside calls.
(i.e. 9.1[2-9]XXXXXXXXX). I then went to the Calling Party Transformations Section and changed Calling Party Number Type to National and Calling Party Numbering Plan to ISDN. For patterns to stations on the Nortel, I set both Calling and Called Party Transformations Sections to Calling Party Number Type Cisco CallManager and CallingParty Numbering Plan to ISDN. And also remember to put the CLID in the External Phone Number Mask in the Line X on Device SEPXXXXXXXXX location.
Let me know if that helped you out
 
I just check and I do not see, "set both Calling and Called Party Transformations Sections to Calling Party Number Type Cisco CallManager and CallingParty Numbering Plan to ISDN."

Our CCM software is: System version: 6.1.5.10000-10
 
We are on CUCM 8, so I can't tell you where to go in 6. But as I said, your Nortel side looks like ours which works with CUCM 8
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top