CLAN ETH-PORT Problem Error Type 3329 AUX 1007 / Test # 1281 Error Cod

[Freedom12]

Hi All,

I would like to share to you some problems I have encountered from our CLAN Connection. We experienced intermittent disconnection with our clan which causes our AES TCP Connection State to be in service / out of service. I performed test board and the result was test number 1281 fail and error code 1007. I also replaced the CLAN Card with a new hardware and with updated firmware load. I've checked the speed and port settings of CLAN Card and Port Settings of our Cisco Switch and both have the same configuration. 100Mbps, Duplex: Full, Auto-Negotiate: NO. Can you enlighten me or can please someone share some information if they have encountered this error before and what was the solutions for this problem.

HARDWARE ERROR REPORT - ACTIVE ALARMS

Port Mtce Alt Err Aux First Last Err Err Rt/ Al Ac
Name Name Type Data Occur Occur Cnt Rt Hr St

02D0617 ETH-PT 3329 1007 09/10/19:05 09/17/04:24 255 1 3 a y
HARDWARE ERROR REPORT - ACTIVE ALARMS

Port Mtce Alt Err Aux First Last Err Err Rt/ Al Ac
Name Name Type Data Occur Occur Cnt Rt Hr St

03D0917 ETH-PT 3329 1007 09/17/03:31 09/17/04:18 6 7 2 a y

TEST RESULTS

Port Maintenance Name Alt. Name Test No. Result Error Code

03D0917 ETH-PT 1281 FAIL 1007
03D0917 ETH-PT 1281 FAIL 1007
03D0917 ETH-PT 1281 FAIL 1007


TEST RESULTS

Port Maintenance Name Alt. Name Test No. Result Error Code

02D0617 ETH-PT 1281 FAIL 1007
02D0617 ETH-PT 1281 FAIL 1007
02D0617 ETH-PT 1281 FAIL 1007

Type: C-LAN
Slot: 03D09
Code/Suffix: TN799 D
Node Name: CLANAES1A
IP Address: 10 .107.201.81
Subnet Mask: 255.255.255.0 Link: 26
Gateway Address: 10 .107.201.1
Enable Ethernet Port? y Allow H.323 Endpoints? y
Network Region: 1 Allow H.248 Gateways? y
VLAN: n Gatekeeper Priority: 5
Target socket load and Warning level: 400
Receive Buffer TCP Window Size: 8320
ETHERNET OPTIONS
Auto? n
Speed: 100Mbps
Duplex: Full

Type: C-LAN
Slot: 02D06
Code/Suffix: TN799 D
Node Name: CLANAES1B
IP Address: 10 .107.201.80
Subnet Mask: 255.255.255.0 Link: 25
Gateway Address: 10 .107.201.1
Enable Ethernet Port? y Allow H.323 Endpoints? y
Network Region: 1 Allow H.248 Gateways? y
VLAN: n Gatekeeper Priority: 5
Target socket load and Warning level: 400
Receive Buffer TCP Window Size: 8320
ETHERNET OPTIONS
Auto? n
Speed: 100Mbps
Duplex: Full

Network Settings

CoreSwitch1.MN.PH>
3/22 PH0-CLanAES1A-01 connected 201 full 100 10/100BaseTX

CoreSwitch2.MN.PH>
3/24 PH0-CLanAES1B-02 connected 201 full 100 10/100BaseTX


Appreciate all your inputs here,

Thanks,
Freedom12

 

[mikeydidit]

Here is the book version of repair procedures for those alarms/errors. I would also do a search at the top of the page on "CLAN" and see what results come back. To me it looks like a routing problem from your core switch.

e. Error Type 1281: System software received an indication that the far end has requested a
disconnect of a session on this link. This is a log-only error.
f. Error Type 1537–1538: Some or all sessions on a port are down
.
1. Test the port (test port location short).
2. Refer to Session Status test (#1286) repair procedure to verify repair.
g. Error Type 1793–1920: System software received an indication that a socket was closed
due to an error.
The error type indicates the application associated with this socket. (Whereas, the Aux Data
indicates the internal application number.)
If: Then the switch raises:
Some sessions are down WARNING alarm on circuit pack
Every session is down MINOR alarm on circuit pack
Error Type Application
1793 Unused
1794 DCS
1795 AUDIX
1796 CMS
1797 ISDN Gateway
1798–1920 Reserved for future


1007 FAIL Ping to the destination failed due to the destination down.
1. Verify that at least one destination reachable through this port is up.
Ping this destination (ping ip-address xxx.xxx.xxx.xxx).
2. If the ping to any destination is successful through this port, the link is
up, although some destinations are unreachable. Ignore the failure.
3. If ping to every destination fails, test this port (test port location
short), and follow the repair procedures for Session Status test
(#1286) failures.


When is the last time you helped someone, just because you were able to?

For the best response to a question, read faq690-6594

 

[Freedom12]

mikeydidit (IS/IT--Management,

Thank you for your time and I checked this also. However I'm looking at CRC Errors as I am extracting logs to the ecs file. I will share also my findings once I have finished this issue. Thank you for your time and effort. Appreciate your inputs here.

Thanks,

Freedom12