Hi, I have a remote access VPN setup on a Cisco 2811 which works fine. Its setup using the cisco VPN client 5.0
I have created various profiles which allow access to different subnet, which works ok and also split tunnelign for internet access.
The issue I have is that when i tru and map a drive, in this case in windows 7.0 \\tower\documents, i can see that the broadcasts are sent out the default route in windows which is :-
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.116 20
10.0.1.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.2.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.6.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.27.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.48.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.55.0 255.255.255.0 On-link 10.0.55.245 276
10.0.55.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.55.245 255.255.255.255 On-link 10.0.55.245 276
However, the drive is actually 10.0.55.102, I have run a wireshark and can see that the broadcast goes as follows-
1439 44.650377000 192.168.0.116 192.168.0.255 NBNS 92 Name query NB TOWER<00>
Any ideas how i can implment something on the 2800 to get round this??? ;-)
Cheers,
S.
I have created various profiles which allow access to different subnet, which works ok and also split tunnelign for internet access.
The issue I have is that when i tru and map a drive, in this case in windows 7.0 \\tower\documents, i can see that the broadcasts are sent out the default route in windows which is :-
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.116 20
10.0.1.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.2.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.6.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.27.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.48.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.55.0 255.255.255.0 On-link 10.0.55.245 276
10.0.55.0 255.255.255.0 10.0.55.1 10.0.55.245 100
10.0.55.245 255.255.255.255 On-link 10.0.55.245 276
However, the drive is actually 10.0.55.102, I have run a wireshark and can see that the broadcast goes as follows-
1439 44.650377000 192.168.0.116 192.168.0.255 NBNS 92 Name query NB TOWER<00>
Any ideas how i can implment something on the 2800 to get round this??? ;-)
Cheers,
S.