Cisco SDM on 2620 2

[JRosario78]

Hi,

I would like to know if the Cisco SDM can be configured on my 2620. My router is not a 2620XM it is just a 2600 series router.

Thanks in advance...

JR

 

[CiscoGuy33]

JRosario78,

No - it does not look like it -

http://www.cisco.com/en/US/products/sw/secursw/ps5318/products_data_sheet0900aecd800fd118.html

Cisco Router and Security Device Manager

Supported Platforms

• Cisco Small-Business 101 Router, Cisco Small-Business 106 Router, Cisco Small-Business 107 Router:
• Cisco IOS Software Release 12.3(8)YG
• Cisco 831 Ethernet Broadband Router, Cisco 836 ADSL over ISDN Broadband Router, and Cisco 837 ADSL Broadband Router:
• Cisco IOS Software Release 12.2(13)ZH or 12.3(2)T
• Cisco 851, 856, 871, 876, 877, and 878 Integrated Services Routers:
• Cisco IOS Software Release 12.3(8)YI
• Cisco 1701 ADSL Security Access Router; Cisco 1710, 1711, and 1712 Security Access Routers; and Cisco 1721, 1751, 1751-V, 1760, and 1760-V Modular Access Routers:
• Cisco IOS Software Release 12.2(13)ZH, 12.2(13)T3, or 12.3(1)M
• Cisco 1801, 1802, 1803, 1811, and 1812 Integrated Services Routers:
• Cisco IOS Software Release 12.3(8)YI
• Cisco 1841 Integrated Services Router:
• Cisco IOS Software Release 12.3(8)T4
• Cisco 2610XM, 2611XM, 2620XM, 2621XM, 2650XM, and 2651XM and Cisco 2691 Multiservice Platforms:
• Cisco IOS Software Release 12.2(15)ZJ3, 12.2(11)T6, or 12.3(1)M
• Cisco 2801, 2811, 2821, and 2851 Integrated Services Routers:
• Cisco IOS Software Release 12.3(8)T4
• Cisco 3725 and 3745 Multiservice Access Routers:
• Cisco IOS Software Release 12.2(15)ZJ3, 12.2(11)T6, or 12.3(1)M
• Cisco 3825 and 3845 Integrated Services Routers:
• Cisco IOS Software Release 12.3(11)T
• Cisco 7204VXR, 7206VXR, and 7301 routers:
• Cisco IOS Software Release 12.3(2)T or 12.3(3)M; no support for B, E, and S trains

hope this helps!


E.A. Broda
CCNA, CCDA, CCAI, Network +

 

[burtsbees]

You can however install SDM on a computer, and then connect to a router and configure it with SDM. In this case, you would need to console into the router first and configure it as such...
router>en
router#conf t
router(config)#ip http server
router(config)#ip http authentication local
router(config)#username xxxx priv 15 password yyyy
router(config)#end
router#wr
Like that---substitute the "xxxx" for your own username, and substitute "yyyy" for your password.

Burt

 

[CiscoGuy33]

Burt,

I will need to try that - I got all 2611s and 2610s here at work in the "Cisco Lab" and plenty of PCs

YOU ARE THE MAN !!!!!!!


E.A. Broda
CCNA, CCDA, CCAI, Network +

 

[burtsbees]

I thought I had done that on my 2620's, but can't remember...it still may not be supported, so don't quote me on that. In fact, now that I think of it, I don't think I had any success, but it's been a while. Maybe Ill try tomorrow...

Burt

 

[burtsbees]

I was wrong---the message pops up saying that it's an unsupported router...

Burt

 

[CiscoGuy33]

Burt,

Thanks anyway - sometimes that is how we all learn the "undocumented" stuff !


E.A. Broda
CCNA, CCDA, CCAI, Network +