I am trying to configure a new T1 in a Cisco 1721(IOS 12.2) Modular Router. I have a Wic1 CSU/DSU card inserted and the line connected. I have setup the DLCI, the LMI type, and the encapsulation method. However it cannot connect. The only information I was given is the following.
Encap - FR-IETF
LMI - ANSI
DLCI - "XXX"
Wan Network ID - X.X.X.X
S Mask - Y.Y.Y.Y
ISP Router IP - Z.Z.Z.Z
My Router IP - A.B.C.D
Then I was given the Lan info which I want to work on after I get the T1 interface connected and pinging. One would think that with so few options it would work easily, but after setting the info all I get are dropped. Below is the sh int from the interface minus the top 2 lines(IP info) Any help would be greatly appreciated. The DLCI seems to always be set to 0 and router discovery is off(cant remember how to activate it)
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 253/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF, loopback not set
Keepalive set (10 sec)
LMI enq sent 223, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 0/3599, interface broadcasts 0
Last input never, output 00:12:37, output hang never
Last clearing of "show interface" counters 01:14:50
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
5287 packets input, 298652 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
22 input errors, 0 CRC, 20 frame, 0 overrun, 0 ignored, 2 abort
304 packets output, 4046 bytes, 0 underruns
0 output errors, 0 collisions, 73 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=down RTS=down CTS=up
Encap - FR-IETF
LMI - ANSI
DLCI - "XXX"
Wan Network ID - X.X.X.X
S Mask - Y.Y.Y.Y
ISP Router IP - Z.Z.Z.Z
My Router IP - A.B.C.D
Then I was given the Lan info which I want to work on after I get the T1 interface connected and pinging. One would think that with so few options it would work easily, but after setting the info all I get are dropped. Below is the sh int from the interface minus the top 2 lines(IP info) Any help would be greatly appreciated. The DLCI seems to always be set to 0 and router discovery is off(cant remember how to activate it)
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 253/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF, loopback not set
Keepalive set (10 sec)
LMI enq sent 223, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 0/3599, interface broadcasts 0
Last input never, output 00:12:37, output hang never
Last clearing of "show interface" counters 01:14:50
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
5287 packets input, 298652 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
22 input errors, 0 CRC, 20 frame, 0 overrun, 0 ignored, 2 abort
304 packets output, 4046 bytes, 0 underruns
0 output errors, 0 collisions, 73 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=down RTS=down CTS=up