Cisco 857 adsl speed slow

[cacas]

hi i have problems with a cisco adsl router 857, the DSL is very slow,
with another telephone company router works well. but the cisco router to

another
business is doing well at a good speed.
the phone company tells me that no noise on the line and that all parameters

are well

show dsl interfa atm 0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x01 0x1
Vendor ID: 'STMI' 'GSPN'
Vendor Specific: 0x0000 0x0007
Vendor Country: 0x0F 0x00
Chip ID: C196 (0)
DFE BOM: DFE3.0 Annex A (1)
Capacity Used: 99% 47%
Noise Margin: 9.0 dB 26.0 dB
Output Power: 8.5 dBm 12.0 dBm
Attenuation: 7.0 dB 4.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0xAC
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 8269 (0 spurious)
PHY Access Err: 0
Activations: 3
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-3.0.014_no_bist.bin
Operation FW: AMR-3.0.014.bin
FW Source: embedded
FW Version: 3.0.14

Interleave Fast Interleave Fast
Speed (kbps): 5216 0 320 0
Cells: 173883 0 1217024 0
Reed-Solomon EC: 77 0 0 0
CRC Errors: 3 0 1 0
Header Errors: 1 0 0 0
Total BER: 8140E-11 0E-0
Leakage Average BER: 8140E-11 0E-0
ATU-R (DS) ATU-C (US)
Bitswap: enabled enabled
Bitswap success: 0 0
Bitswap failure: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
000: 0 0 0 0 0 0 0 0 2 3 4 5 5 6 6 6
010: 6 6 6 6 6 5 6 5 5 5 4 4 4 3 2 2
020: 0 7 8 8 9 9 9 8 9 8 8 8 8 8 8 8
030: 8 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9
040: 0 9 9 9 9 9 9 9 9 9 9 9 9 9 2 9
050: 9 9 9 9 8 9 9 9 8 8 8 8 9 8 8 8
060: 8 8 8 8 8 8 8 8 9 8 8 8 8 8 8 8
070: 8 8 8 8 8 8 7 8 7 7 7 7 7 7 7 7
080: 7 7 7 7 7 7 6 6 6 7 7 7 7 7 7 6
090: 6 6 7 7 7 7 7 6 7 7 7 7 7 7 7 7
0A0: 6 7 7 7 7 7 6 6 7 6 6 6 6 6 6 6
0B0: 6 6 6 6 6 6 6 5 5 5 5 5 5 5 5 5
0C0: 5 5 5 5 5 5 5 5 5 5 5 5 6 5 5 5
0D0: 6 5 5 6 6 6 6 6 6 6 6 6 6 6 6 5
0E0: 6 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6
0F0: 6 6 6 6 6 7 7 7 7 8 7 7 7 7 8 8

DSL: Training log buffer capability is not enabled


=================================================

yourname# sh controller atm 0/0  
Interface: ATM0, Hardware: MPC ATMSAR (with Alcatel ADSL Module), State: up
IDB: 0x823F6A9C Instance: 0x823F7BDC PHY Inst: 0x825197C0 us_bwidth: 320
Slot: 0 Unit: 0 pkt Size: 4528
Sar ctrl queue: max depth = 0, current queue depth = 0,
drops = 0, urun cnt = 0, total cnt = 0

<* ATM Parameter RAM *>
RCELL_TMP_BASE = 0x000008C0, TCELL_TMP_BASE = 0x00000900, UDC_TMP_BASE = 0x00000000, INT_RCT_BASE = 0x00009400
INT_TCT_BASE = 0x00009580, INT_TCTE_BASE = 0x00009700, APCP_BASE = 0x00000940, INTT_BASE = 0x00009880
BD_BASE_EXT = 0x03000000, VPT_BASE = 0x680498C0, VCT_BASE = 0x03CA31C0, VP_MASK = 0x0000003F
CRC32_PRES = 0xFFFFFFFF, CRC32_MASK = 0xDEBB20E3, IDLE_BASE = 0x000099C0, IDLE_SIZE = 0x00000034
VCIF = 0x00000000, GMODE = 0x00000009, COMM_INFO(0x86) = 0x00000002, COMM_INFO(0x88) = 0x00020000

<* APC Parameters *>
APCL_FIRST = 0x00000960, APCL_LAST = 0x00000970, APCL_PTR = 0x00000960
CPS = 0x00000001, CPS_CNT = 0x00000001, MAX_IT = 0x00000001
REAL_TSTP = 0x004476B8, APC_STATE = 0x00000000

--More--  <* APC Pri & Schedule Tables *>
Level 1 : Base = 0x00009A00, End = 0x00009A14, Rptr = 0x00009A04, Sptr = 0x00009A02
(0x68049A00 0x0000) (0x68049A02 0x0000) (0x68049A04 0x0000) (0x68049A06 0x0000)
(0x68049A08 0x0001) (0x68049A0A 0x0000) (0x68049A0C 0x0000) (0x68049A0E 0x0000)
(0x68049A10 0x0000) (0x68049A12 0x0000) (0x68049A14 0x0000) (0x68049A16 0x8000)
Level 2 : Base = 0x00009A18, End = 0x00009A2C, Rptr = 0x00009A1C, Sptr = 0x00009A1A
(0x68049A18 0x0000) (0x68049A1A 0x0000) (0x68049A1C 0x0000) (0x68049A1E 0x0000)
(0x68049A20 0x0000) (0x68049A22 0x0000) (0x68049A24 0x0000) (0x68049A26 0x0000)
(0x68049A28 0x0000) (0x68049A2A 0x0000) (0x68049A2C 0x0000) (0x68049A2E 0x8000)
Level 3 : Base = 0x00009A30, End = 0x00009A44, Rptr = 0x00009A34, Sptr = 0x00009A32
(0x68049A30 0x0000) (0x68049A32 0x0000) (0x68049A34 0x0002) (0x68049A36 0x0000)
(0x68049A38 0x0000) (0x68049A3A 0x0000) (0x68049A3C 0x0000) (0x68049A3E 0x0000)
--More--   (0x68049A40 0x0000) (0x68049A42 0x0000) (0x68049A44 0x0000) (0x68049A46 0x8000)


<* Interrupt Queue Information *>
Interrupt Queue 0 SWIntqEntry 3CA30FC
Interrupt Queue 1 SWIntqEntry 3CA3128
Interrupt Queue 2 SWIntqEntry 3CA3140
Interrupt Queue 3 SWIntqEntry 3CA3180


<* Channel Parameters *>

Channel [TxBD Base . Tx Cur BD . Tx Conf BD] [RxBD Base . Rx Cur BD] RCT TCT MRBLR
----------------------------------------------------------------------------------------------------
1 [0x03CA1EC0 0x03CA1EC0 0x03CA1EC0] [0x03CA24C0 0x03CA24C0] 0x68049420 0x680495A0 0x00000000


<* Channel (01) TCT *>
TCT Status = 0x10040000, TxDBPtr = 0xDFDA94CF, TBDCnt = 0x0000C2FC, TBDOff = 0x00000000
--More--  RateRem = 0x0000000C, PCRFra = 0x00000034, PCR = 0x00000003, AAL0 CR10 = 0x00000040
APCLC = 0x00000000, CellHdr = 0x00000000, TxBDBase misc = 0x00CA1EC2

<* Channel (01) Tx BDs *>
# BD Status-Length Data Buffer
-----------------------------------------
0 0x03CA1EC0 0x10000000 0x00000000


<* Channel (01) RCT *>
RCT Status = 0x10000000, RxDBPtr = 0x7C51E76F, Time Stamp = 0xB739EAFF, RBDOff = 0x00000000
AAL Bits = 0x00000040, MRBLR = 0x00000000, RxBDBase = 0x00CA24C0

<* Channel (01) Rx BDs *>
RxPoolCurrent = 0x00000000, RxPoolNext = 0x00000010
# BD Status Data Buffer [tBuffer . Particle . Size . Rx Buffer]
----------------------------------------------------------------------------------------
0 0x03CA24C0 0x90000000 0x03D48A40 [0x8252742C 0x00000000 0x00000000 0x00000000]
--More--   1 0x03CA24C8 0x90000000 0x03D48900 [0x82527458 0x00000000 0x00000000 0x00000000]
2 0x03CA24D0 0x90000000 0x03D487C0 [0x82527484 0x00000000 0x00000000 0x00000000]
3 0x03CA24D8 0x90000000 0x03D48680 [0x825274B0 0x00000000 0x00000000 0x00000000]
4 0x03CA24E0 0x90000000 0x03D48540 [0x825274DC 0x00000000 0x00000000 0x00000000]
5 0x03CA24E8 0x90000000 0x03D48400 [0x82527508 0x00000000 0x00000000 0x00000000]
6 0x03CA24F0 0x90000000 0x03D482C0 [0x82527534 0x00000000 0x00000000 0x00000000]
7 0x03CA24F8 0x90000000 0x03D48180 [0x82527560 0x00000000 0x00000000 0x00000000]
8 0x03CA2500 0x90000000 0x03D48040 [0x8252758C 0x00000000 0x00000000 0x00000000]
9 0x03CA2508 0x90000000 0x03D47F00 [0x825275B8 0x00000000 0x00000000 0x00000000]
10 0x03CA2510 0x90000000 0x03D47DC0 [0x825275E4 0x00000000 0x00000000 0x00000000]
11 0x03CA2518 0x90000000 0x03D47C80 [0x82527610 0x00000000 0x00000000 0x00000000]
12 0x03CA2520 0x90000000 0x03D47B40 [0x8252763C 0x00000000 0x00000000 0x00000000]
--More--   13 0x03CA2528 0x90000000 0x03D47A00 [0x82527668 0x00000000 0x00000000 0x00000000]
14 0x03CA2530 0x90000000 0x03D478C0 [0x82527694 0x00000000 0x00000000 0x00000000]
15 0x03CA2538 0xB0000000 0x03D47780 [0x825276C0 0x00000000 0x00000000 0x00000000]

<* Channel (01) Statistics *>
Transmitted : bytes = 0, cells = 0, frames = 0
Received: bytes = 0, cells = 0, frames = 0, errors = 0
Received frames: CRC32 error = 0, length error = 0
reassembly timeouts = 0, CLP = 0, PTI congestion = 0
discarded: cells = 0, frames = 0

<* Channel Parameters *>

Channel [TxBD Base . Tx Cur BD . Tx Conf BD] [RxBD Base . Rx Cur BD] RCT TCT MRBLR
----------------------------------------------------------------------------------------------------
2 [0x03CA20C0 0x03CA2108 0x03CA2108] [0x03CA26C0 0x03CA26C8] 0x68049440 0x680495C0 0x00000600

--More--  
<* Channel (02) TCT *>
TCT Status = 0x10040002, TxDBPtr = 0x03B0F8F2, TBDCnt = 0x00000000, TBDOff = 0x00000048
RateRem = 0x00000000, PCRFra = 0x00000000, PCR = 0x00000001, AAL5 CRC = 0xC434118D TML = 0x005C
APCLC = 0x00000000, CellHdr = 0x00800200, TxBDBase misc = 0x00CA20C2

<* Channel (02) Tx BDs *>
# BD Status-Length Data Buffer
-----------------------------------------
0 0x03CA20C0 0x00000000 0x03B13856
1 0x03CA20C8 0x00000000 0x03B17816
2 0x03CA20D0 0x00000000 0x03B29D56
3 0x03CA20D8 0x00000000 0x03D4B858
4 0x03CA20E0 0x00000000 0x03B171B6
5 0x03CA20E8 0x00000000 0x03B12B96
6 0x03CA20F0 0x00000000 0x03B24A76
7 0x03CA20F8 0x00000000 0x03B296F6
8 0x03CA2100 0x00000000 0x03B0F896
9 0x03CA2108 0x00000000 0x03B27716


--More--  <* Channel (02) RCT *>
RCT Status = 0x10310002, RxDBPtr = 0x03A53860, Time Stamp = 0xBF59D493, RBDOff = 0x00000010
AAL Bits = 0x00000090, MRBLR = 0x00000600, RxBDBase = 0x00CA26C0

<* Channel (02) Rx BDs *>
RxPoolCurrent = 0x00000012, RxPoolNext = 0x00000002
# BD Status Data Buffer [tBuffer . Particle . Size . Rx Buffer]
----------------------------------------------------------------------------------------
0 0x03CA26C0 0x80000000 0x03A4E520 [0x82524B00 0x82365940 0x000005FE 0x03A4E520]
1 0x03CA26C8 0x80000000 0x03A4DEC0 [0x82524B24 0x82365900 0x000005FE 0x03A4DEC0]
2 0x03CA26D0 0x80000000 0x03A531A0 [0x82524B48 0x823658C0 0x000005FE 0x03A4D860]
3 0x03CA26D8 0x80000000 0x03A52B40 [0x82524B6C 0x82365240 0x000005FE 0x03A631E0]
4 0x03CA26E0 0x80000000 0x03A524E0 [0x82524B90 0x82365200 0x000005FE 0x03A62B80]
5 0x03CA26E8 0x80000000 0x03A63EA0 [0x82524BB4 0x82365880 0x000005FE 0x03A4D200]
--More--   6 0x03CA26F0 0x80000000 0x03A51E80 [0x82524BD8 0x82365840 0x000005FE 0x03A4CBA0]
7 0x03CA26F8 0x80000000 0x03A51820 [0x82524BFC 0x82365800 0x000005FE 0x03A4C540]
8 0x03CA2700 0x80000000 0x03A63840 [0x82524C20 0x823657C0 0x000005FE 0x03A4BEE0]
9 0x03CA2708 0x80000000 0x03A511C0 [0x82524C44 0x82365780 0x000005FE 0x03A4B880]
10 0x03CA2710 0x80000000 0x03A50B60 [0x82524C68 0x82365740 0x000005FE 0x03A4B220]
11 0x03CA2718 0x80000000 0x03A50500 [0x82524C8C 0x823651C0 0x000005FE 0x03A62520]
12 0x03CA2720 0x80000000 0x03A4FEA0 [0x82524CB0 0x82365180 0x000005FE 0x03A61EC0]
13 0x03CA2728 0x80000000 0x03A4F840 [0x82524CD4 0x82365140 0x000005FE 0x03A61860]
14 0x03CA2730 0x80000000 0x03A4F1E0 [0x82524CF8 0x82365100 0x000005FE 0x03A61200]
15 0x03CA2738 0xA0000000 0x03A4EB80 [0x82524D1C 0x823650C0 0x000005FE 0x03A60BA0]

<* Channel (02) Statistics *>
Transmitted : bytes = 210666134, cells = 4391797, frames = 5947
--More--   Received: bytes = 6469411, cells = 136531, frames = 7630, errors = 0
Received frames: CRC32 error = 0, length error = 0
reassembly timeouts = 0, CLP = 7633, PTI congestion = 6
discarded: cells = 0, frames = 0

VC QoS Summary
--------------
Active Configured Scheduled
Connections
VCD VPI VCI COS PCR SCR/MCR COS PCR SCR/MCR
--- -------- -------- ------ ------- -------- ------- --------
1 8 32 UBR 0 n/a UBR 320 n/a


Connections RX RX RX RX TX TX TX
VCD VPI/ VCI AAL5 RAW Chain Drop AAL5 RAW Drop
--- --- ----- ----- ----- ----- ----- ----- ----- -----
1 8 /32

Oam pak statistics:
Oam paks waiting for tx for each vcd(vcd/count/drop)
1/0/0 2/0/0 3/0/0 4/0/0 5/0/0 6/0/0 7/0/0 8/0/0
9/0/0 10/0/0
--More--  Misc Oam Drops: 0

yourname#


thank

 

[burtsbees]

int atm0/0
clock rate aal5 7000000
clock rate aal2 2600000

See if that helps---I have 6 down and 500 or so up,and I had to do that...

Edge#sh run int atm0/0
Building configuration...

Current configuration : 240 bytes
!
interface ATM0/0
no ip address
ip verify unicast reverse-path
no ip redirects
no ip unreachables
ip accounting access-violations
no atm ilmi-keepalive
dsl operating-mode auto
clock rate aal5 7000000
clock rate aal2 2600000
end

Edge#sh dsl int atm0/0
ATM0/0
Alcatel 20150 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x01 0x1
Vendor ID: 'ALCB' ' '
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x00
Capacity Used: 98% 97%
Noise Margin: 6.0 dB 7.0 dB
Output Power: 16.5 dBm 12.0 dBm
Attenuation: 24.0 dB 31.5 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 2651 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
SW Version: 3.8131
FW Version: 0x1A04

Interleave Fast Interleave Fast
Speed (kbps): 0 6016 0 608
Cells: 0 72916743 0 1551403681
Reed-Solomon EC: 0 0 3 3
CRC Errors: 0 5040 6 53915
Header Errors: 0 3983 6 15451
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 5 4 7 8 9 9 9 9 8
10: 9 8 9 8 8 8 8 8 8 7 7 7 6 7 0 0
20: 0 0 0 0 0 0 4 5 5 6 7 7 8 9 9 A
30: A B B C C C D D D D D D D D D D
40: D D D D D D D D D D 2 D D D D D
50: D D D D D D D D D D D D D C C C
60: D C C C C C C C C C C C C C C C
70: C C C C C C C C C C C C C B B 8
80: 8 B B C C C C C C B C C C C C C
90: C C 7 B C B C B C C B C C C C C
A0: 9 B C B B C C C C B B B B B B 0
B0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

/

tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!

 

[cacas]

hello

I Have a problem, because not recognize the command

int int atm0 (ok)


clock rate aal5 7000000
not reognize command clock ?

I am doing wrong ?

thank

 

[burtsbees]

post the output...

router>en
router#conf t
router(config)#int atm0
router(config-if)#?

/

tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!

 

[cacas]

?
Interface configuration commands:
access-expression Build a bridge boolean access expression
arp Set arp type (arpa, probe, snap) or timeout or log
options
atm Modify ATM parameters
backup Modify backup parameters
bandwidth Set bandwidth informational parameter
bgp-policy Apply policy propagated by bgp community string
bridge-group Transparent bridging interface parameters
carrier-delay Specify delay for interface transitions
cdp CDP interface subcommands
class-int Configure default vc-class name
crypto Encryption/Decryption commands
dampening Enable event dampening
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
dot1q dot1q interface configuration commands
dot1x Interface Config Commands for IEEE 802.1X
dsl ADSL subcommands
eou EAPoUDP Interface Configuration Commands
exit Exit from interface configuration mode
fair-queue Enable Fair Queuing on an Interface
flow-sampler Attach flow sampler to the interface
help Description of the interactive help system
hold-queue Set hold queue depth
ip Interface Internet Protocol config commands
iphc-profile Configure IPHC profile
l2-filter Set Layer2 ACL for packet received by upper layer
protocols
load-interval Specify interval for load calculation for an
interface
logging Configure logging for interface
loopback Configure internal loopback on an interface
mac-address Manually set interface MAC address
macro Command macro
max-reserved-bandwidth Maximum Reservable Bandwidth on an Interface
mtu Set the interface Maximum Transmission Unit (MTU)
no Negate a command or set its defaults
pvc Configure ATM PVC parameters
rate-limit Rate Limit
routing Per-interface routing configuration
service-policy Configure QoS Service Policy
shutdown Shutdown the selected interface
snmp Modify SNMP interface parameters
timeout Define timeout values for this interface
transmit-interface Assign a transmit interface to a receive-only
interface
zone-member Apply zone name

yourname(config-if)#atm ?
address-registration Address Registration
auto-configuration ATM interface auto configuration
bandwidth Allow bandwidth change on ATM PVCs
clock ATM TX clock source
e164 E164 Configuration
ilmi-enable ILMI Configuration
ilmi-keepalive Keepalive polling configuration
ilmi-pvc-discovery Enable ILMI PVC Discovery
oversubscribe Allow oversubscription of ATM link
pppatm PPP over ATM
pvc Create a PVC
sonet ATM SONET mode
vc-per-vp ATM VCIs per VPI

yourname(config-if)#atm clock ?
INTERNAL Internally generated TX clock

 

[burtsbees]

I would say that if it works well with one telco, but not the other, and everything in the interface stats looks fine, then deductive reasoning dictates that it must be the telco. Tell them that, though you are not likely to get anywhere, as most telco's (in my experience) like to blame the customer equipment for everything, due to their severe lack of common sense.

/


tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!

 

[cacas]

can be for the version of IOS,
the version of IOS: 12.4 (15) T7
this router does not support these commands?

Thank

 

[cacas]

hello,
I write all the settings. if there is something wrong


version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname yourname
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
!
aaa new-model
!
!
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authorization exec default local
aaa authorization network sdm_vpn_group_ml_1 local
!
!
aaa session-id common
!
crypto pki trustpoint TP-self-signed-2994811081
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2994811081
revocation-check none
rsakeypair TP-self-signed-2994811081
!
!
crypto pki certificate chain TP-self-signed-2994811081
certificate self-signed 01 nvram:IOS-Self-Sig#4.cer
dot11 syslog
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.0.1
ip dhcp excluded-address 192.168.0.36 192.168.0.254
!
ip dhcp pool sdm-pool
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.201
dns-server 195.235.113.3 195.235.96.90
lease 0 2
!
!
ip cef
no ip domain lookup
ip domain name yourdomain.com
!
!
!
username xxxx privilege 15 password 0 xxxxx
username xxx secret 5
!
!
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp client configuration group xxxxxxx
key xxxxxxxxxxx
pool SDM_POOL_1
!
crypto isakmp client configuration group xxxxxxx
key xxxxxxxxxxx
pool SDM_POOL_2
crypto isakmp profile sdm-ike-profile-1
match identity group xxxxxxxxx
match identity group xxxxxxxxxx
client authentication list sdm_vpn_xauth_ml_1
isakmp authorization list sdm_vpn_group_ml_1
client configuration address respond
virtual-template 1
!
!
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
!
crypto ipsec profile SDM_Profile1
set transform-set ESP-3DES-SHA
set isakmp-profile sdm-ike-profile-1
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
pvc 8/32
pppoe-client dial-pool-number 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Virtual-Template1 type tunnel
ip unnumbered Dialer0
tunnel mode ipsec ipv4
tunnel protection ipsec profile SDM_Profile1
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 192.168.0.201 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
!
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap callin
ppp pap sent-username xxxxxxxxxx password 0 xxxxxxxxxxxx
!
ip local pool SDM_POOL_1 192.168.0.240 192.168.0.254
ip local pool SDM_POOL_2 192.168.0.230 192.168.0.235
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 192.168.0.0
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 23 permit 192.168.0.0
access-list 23 permit 10.10.10.0 0.0.0.7
access-list 23 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------

Cisco Router and Security Device Manager (SDM) is installed on this device and
it provides the default username "cisco" for one-time use. If you have already
used the username "cisco" to login to the router and your IOS image supports the
"one-time" user option, then this username has already expired. You will not be
able to login to the router with this username after you exit this session.

It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.

username <myuser> privilege 15 secret 0 <mypassword>

Replace <myuser> and <mypassword> with the username and password you want to
use.

-----------------------------------------------------------------------
^C
banner login ^C
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
--More--  with the password "cisco". The default username and password have a privilege level of 15.

Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.

username <myuser> privilege 15 secret 0 <mypassword>
no username cisco

Replace <myuser> and <mypassword> with the username and password you want to use.

For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to

http://www.cisco.com/go/sdm

-----------------------------------------------------------------------