Cisco 837 Configuration

[RandomlyAdam]

Hey all,

I've tried without any success to setup a Cisco 837 to a non-pppoe DSL connection. The connection is Verizon ADSL with aal5snap encapsulation with a static IP. Here's my current config. What did I do wrong?

-ap

version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 *********
enable password *********
!
no aaa new-model
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool routerDHCP
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 216.139.32.37 216.139.32.45
!
!
ip cef
ip name-server 216.139.32.37
ip name-server 216.139.32.45
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
username CRWS_Gayatri privilege 15 password 0
***********
!
!
!
!
bridge irb
!
!
interface Ethernet0
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
hold-queue 100 out
!
interface Ethernet2
no ip address
shutdown
hold-queue 100 out
!
interface ATM0
ip address 216.139.x.x 255.255.255.0
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/35
encapsulation aal5snap
!
!
interface FastEthernet1
speed auto
full-duplex
!
interface FastEthernet2
speed auto
full-duplex
!
interface FastEthernet3
speed auto
full-duplex
!
interface FastEthernet4
speed auto
full-duplex
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 216.139.x.1
!
ip http server
no ip http secure-server
!
ip nat translation max-entries 1000
ip nat inside source list 1 interface ATM0 overload
!
access-list 1 permit 10.10.10.0 0.0.0.255
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 120 0
password cisco
login local
length 0
!
scheduler max-task-time 5000
end

 

[burtsbees]

Try this
int atm0
no ip add
no pvc 0/35
no encaps
int atm0.1 point-to-point
no snmp trap link-status
pvc 0/35
oam-pvc manage
pppoa-client dial-pool-number 1
int di0
ip add 216.139.x.x 255.255.255.0
no ip red
ip nat outside
ip virtual-reassembly
encaps aal5snap

Now the question is...do you have to authenticate with ppp?

Burt

 

[burtsbees]

Also, try SDM---it's free, and it will configure your 837 with a GUI---very simple to use! Let me know if you need a copy
timandlizh at gmail dot com

Burt

 

[RandomlyAdam]

Burt, I'll try what you suggested, and there's no PPP authentication. I managed to find SDM lastnight and dinked around with it for a few hours with no success.

 

[RandomlyAdam]

Burt,

That didn't fix the problem... Not sure what you need to know from here... I checked with the ISP the router isn't showing up in their ARP table.

-Adam

 

[burtsbees]

What happened with SDM? I'm good with PPPoE, but not PPPoA, with no authentication...

Burt

 

[RandomlyAdam]

Burt,

It was able to configure the router, but i guess not correctly. As far as PPP goes, this ISP doesn't use it on their DSL connections.

-Adam

 

[burtsbees]

If it's not considered point to point, what else could it be? Or just no chap or pap?


Burt

 

[RandomlyAdam]

Burt,

My bad, it is PPP. Just no chap or pap.

-adam