Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Cisco 761
- Thread starter thecokey
- Start date
CiscoGuy33
Instructor
thecokey,
They just need any one of several different "free" TFTP software programs running on a PC. Make sure the TFTP is running and you know the IP address of the PC.
On the router he will need to go into privledged mode by typing in ena and the password.
I always "ping" the TFTP first just to make sure I can reach it -
router# ping 192.168.1.99 (or whatever IP of the PC with the TFTP running)
Then he just types -
router# copy start tftp
Then just follow the promps, should ask the IP address of the TFTP server next (the PC running TFTP software) and then what you want to call it.
This will send a copy of the start-up config which is what router loads on boot and is running unless he has made changes and not saved them.
All he has to do is go to the folder that the TFTP uses and send that file to you as an attachment in an email, they are rather small files!!
Hope this helps!!
E.A. Broda
CCNA, CCDA, CCAI, Network +
- Thread starter
- #3
Hi
Thanks for the reply.
I have now moved on slightly
We have as Cisco 2600 with a dialer profile for the Cisco 761.
We have a successful connection.
When I try to telnet the router it appears as though a connection is made but I am not presented with any prompt!
When the user does this from their LAN they are presented with password prompt.
There are no odd NAT rules anywhere and I am now completely confused!
Is our 2600 doing something strange with telnet emulation??
Any help would be greatly appreciated.
Kind regards
Col
Thanks for the reply.
I have now moved on slightly
We have as Cisco 2600 with a dialer profile for the Cisco 761.
We have a successful connection.
When I try to telnet the router it appears as though a connection is made but I am not presented with any prompt!
When the user does this from their LAN they are presented with password prompt.
There are no odd NAT rules anywhere and I am now completely confused!
Is our 2600 doing something strange with telnet emulation??
Any help would be greatly appreciated.
Kind regards
Col
CiscoGuy33
Instructor
thecokey,
It would help if you post a copy of the "Show run" (XXXX out your password info).
It could be several different things but it helps if we see the config so we can tell you exactly what is wrong and how to fix it on YOUR config!!
Hope this helps
E.A. Broda
CCNA, CCDA, CCAI, Network +
- Thread starter
- #6
Hi
Apreciate the help, here is the conf:
SET SCREENLENGTH 20
SET COUNTRYGROUP 1
SET LAN MODE ANY
SET WAN MODE ONLY
SET AGE OFF
SET MULTIDESTINATION ON
SET SWITCH NET3
SET ALAWVOICE ON
SET INTERNALTONES NONE
SET 1 DELAY 30
SET 2 DELAY 30
SET BRIDGING ON
SET LEARN ON
SET PASSTHRU OFF
SET SPEED AUTO
SET PLAN NORMAL
SET 1 AUTO ON
SET 2 AUTO ON
SET 1 NUMBER
SET 2 NUMBER
SET 1 BACKUPNUMBER
SET 2 BACKUPNUMBER
SET 1 RINGBACK
SET 2 RINGBACK
SET 1 CLIVALIDATENUMBER
SET 2 CLIVALIDATENUMBER
SET CLICALLBACK OFF
SET CLIAUTHENTICATION OFF
SET SYSTEMNAME XOM1
LOG CALLS
LOG ERRORS
SET UNICASTFILTER OFF
DEMAND 1 THRESHOLD 0
DEMAND 2 THRESHOLD 48
DEMAND 1 DURATION 1
DEMAND 2 DURATION 1
DEMAND 1 SOURCE LAN
DEMAND 2 SOURCE BOTH
TIMEOUT 1 THRESHOLD 0
TIMEOUT 2 THRESHOLD 48
TIMEOUT 1 DURATION 0
TIMEOUT 2 DURATION 0
TIMEOUT 1 SOURCE LAN
TIMEOUT 2 SOURCE BOTH
SET AOCDTIMEOUT OFF
SET PASSWORD SYSTEM ENCRYPTED 104f1b10041917
SET REMOTEACCESS PROTECTED
SET LOCALACCESS PROTECTED
SET CLICKSTART ON
SET LOGOUT 0
SET CALLERID OFF
SET PPP AUTHENTICATION IN CHAP
SET PPP CHAPREFUSE NONE
SET PPP AUTHENTICATION OUT NONE
SET PPP AUTHENTICATION ACCEPT EITHER
SET PPP TAS CLIENT 0.0.0.0
SET PPP TAS CHAPSECRET LOCAL ON
SET PPP CALLBACK REQUEST OFF
SET PPP CALLBACK REPLY OFF
SET PPP NEGOTIATION INTEGRITY 10
SET PPP NEGOTIATION COUNT 10
SET PPP NEGOTIATION RETRY 3000
SET PPP TERMREQ COUNT 2
SET PPP MULTILINK OFF
SET COMPRESSION STAC
SET PPP BACP ON
SET PPP ADDRESS NEGOTIATION LOCAL OFF
SET PPP IP NETMASK LOCAL OFF
SET IP PAT UDPTIMEOUT 5
SET IP PAT TCPTIMEOUT 30
SET IP PAT PORTHANDLER FTP 10.4.128.129
SET IP RIP TIME 30
SET CALLDURATION 0
SET SNMP CONTACT ""
SET SNMP LOCATION ""
SET SNMP TRAP COLDSTART OFF
SET SNMP TRAP WARMSTART OFF
SET SNMP TRAP LINKDOWN OFF
SET SNMP TRAP LINKUP OFF
SET SNMP TRAP AUTHENTICATIONFAIL OFF
SET DHCP OFF
SET DHCP DOMAIN
SET DHCP NETBIOS_SCOPE
SET CALLTIME VOICE INCOMING OFF
SET CALLTIME VOICE OUTGOING OFF
SET CALLTIME DATA INCOMING OFF
SET CALLTIME DATA OUTGOING OFF
SET USER LAN
SET IP ROUTING ON
SET IP ADDRESS 10.4.128.142
SET IP NETMASK 255.255.255.240
SET IP FRAMING ETHERNET_II
SET IP PROPAGATE ON
SET IP COST 1
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET USER Internal
SET IP ADDRESS 0.0.0.0
SET IP NETMASK 0.0.0.0
SET IP FRAMING ETHERNET_II
SET IP PROPAGATE ON
SET IP COST 1
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET USER Standard
SET PROFILE ID 000000000000
SET PROFILE POWERUP ACTIVATE
SET PROFILE DISCONNECT KEEP
SET IP ROUTING ON
SET IP ADDRESS 0.0.0.0
SET IP NETMASK 0.0.0.0
SET IP FRAMING NONE
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET USER GML1
SET PROFILE ID 000000000000
SET PROFILE POWERUP ACTIVATE
SET PROFILE DISCONNECT KEEP
SET BRIDGING OFF
SET 1 NUMBER XXXXXXXXXXXXXX
SET 2 NUMBER XXXXXXXXXXXXXX
TIMEOUT 1 DURATION 60
SET PPP AUTHENTICATION OUT CHAP
SET PPP CLIENTNAME XOM1
SET PPP PASSWORD CLIENT ENCRYPTED XXXXXXXXXXXXXX
SET PPP SECRET CLIENT ENCRYPTED XXXXXXXXXXXXXX
SET PPP PASSWORD HOST ENCRYPTED XXXXXXXXXXXXXX
SET PPP SECRET HOST ENCRYPTED XXXXXXXXXXXXXX
SET IP ROUTING ON
SET IP ADDRESS 10.4.128.201
SET IP NETMASK 255.255.255.0
SET IP FRAMING NONE
SET IP PROPAGATE ON
SET IP COST 1
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET IP ROUTE DEST 10.4.128.0/24 GATEWAY 10.4.128.200 PROPAGATE ON COST 1
Kind regards
Col
Apreciate the help, here is the conf:
SET SCREENLENGTH 20
SET COUNTRYGROUP 1
SET LAN MODE ANY
SET WAN MODE ONLY
SET AGE OFF
SET MULTIDESTINATION ON
SET SWITCH NET3
SET ALAWVOICE ON
SET INTERNALTONES NONE
SET 1 DELAY 30
SET 2 DELAY 30
SET BRIDGING ON
SET LEARN ON
SET PASSTHRU OFF
SET SPEED AUTO
SET PLAN NORMAL
SET 1 AUTO ON
SET 2 AUTO ON
SET 1 NUMBER
SET 2 NUMBER
SET 1 BACKUPNUMBER
SET 2 BACKUPNUMBER
SET 1 RINGBACK
SET 2 RINGBACK
SET 1 CLIVALIDATENUMBER
SET 2 CLIVALIDATENUMBER
SET CLICALLBACK OFF
SET CLIAUTHENTICATION OFF
SET SYSTEMNAME XOM1
LOG CALLS
LOG ERRORS
SET UNICASTFILTER OFF
DEMAND 1 THRESHOLD 0
DEMAND 2 THRESHOLD 48
DEMAND 1 DURATION 1
DEMAND 2 DURATION 1
DEMAND 1 SOURCE LAN
DEMAND 2 SOURCE BOTH
TIMEOUT 1 THRESHOLD 0
TIMEOUT 2 THRESHOLD 48
TIMEOUT 1 DURATION 0
TIMEOUT 2 DURATION 0
TIMEOUT 1 SOURCE LAN
TIMEOUT 2 SOURCE BOTH
SET AOCDTIMEOUT OFF
SET PASSWORD SYSTEM ENCRYPTED 104f1b10041917
SET REMOTEACCESS PROTECTED
SET LOCALACCESS PROTECTED
SET CLICKSTART ON
SET LOGOUT 0
SET CALLERID OFF
SET PPP AUTHENTICATION IN CHAP
SET PPP CHAPREFUSE NONE
SET PPP AUTHENTICATION OUT NONE
SET PPP AUTHENTICATION ACCEPT EITHER
SET PPP TAS CLIENT 0.0.0.0
SET PPP TAS CHAPSECRET LOCAL ON
SET PPP CALLBACK REQUEST OFF
SET PPP CALLBACK REPLY OFF
SET PPP NEGOTIATION INTEGRITY 10
SET PPP NEGOTIATION COUNT 10
SET PPP NEGOTIATION RETRY 3000
SET PPP TERMREQ COUNT 2
SET PPP MULTILINK OFF
SET COMPRESSION STAC
SET PPP BACP ON
SET PPP ADDRESS NEGOTIATION LOCAL OFF
SET PPP IP NETMASK LOCAL OFF
SET IP PAT UDPTIMEOUT 5
SET IP PAT TCPTIMEOUT 30
SET IP PAT PORTHANDLER FTP 10.4.128.129
SET IP RIP TIME 30
SET CALLDURATION 0
SET SNMP CONTACT ""
SET SNMP LOCATION ""
SET SNMP TRAP COLDSTART OFF
SET SNMP TRAP WARMSTART OFF
SET SNMP TRAP LINKDOWN OFF
SET SNMP TRAP LINKUP OFF
SET SNMP TRAP AUTHENTICATIONFAIL OFF
SET DHCP OFF
SET DHCP DOMAIN
SET DHCP NETBIOS_SCOPE
SET CALLTIME VOICE INCOMING OFF
SET CALLTIME VOICE OUTGOING OFF
SET CALLTIME DATA INCOMING OFF
SET CALLTIME DATA OUTGOING OFF
SET USER LAN
SET IP ROUTING ON
SET IP ADDRESS 10.4.128.142
SET IP NETMASK 255.255.255.240
SET IP FRAMING ETHERNET_II
SET IP PROPAGATE ON
SET IP COST 1
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET USER Internal
SET IP ADDRESS 0.0.0.0
SET IP NETMASK 0.0.0.0
SET IP FRAMING ETHERNET_II
SET IP PROPAGATE ON
SET IP COST 1
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET USER Standard
SET PROFILE ID 000000000000
SET PROFILE POWERUP ACTIVATE
SET PROFILE DISCONNECT KEEP
SET IP ROUTING ON
SET IP ADDRESS 0.0.0.0
SET IP NETMASK 0.0.0.0
SET IP FRAMING NONE
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET USER GML1
SET PROFILE ID 000000000000
SET PROFILE POWERUP ACTIVATE
SET PROFILE DISCONNECT KEEP
SET BRIDGING OFF
SET 1 NUMBER XXXXXXXXXXXXXX
SET 2 NUMBER XXXXXXXXXXXXXX
TIMEOUT 1 DURATION 60
SET PPP AUTHENTICATION OUT CHAP
SET PPP CLIENTNAME XOM1
SET PPP PASSWORD CLIENT ENCRYPTED XXXXXXXXXXXXXX
SET PPP SECRET CLIENT ENCRYPTED XXXXXXXXXXXXXX
SET PPP PASSWORD HOST ENCRYPTED XXXXXXXXXXXXXX
SET PPP SECRET HOST ENCRYPTED XXXXXXXXXXXXXX
SET IP ROUTING ON
SET IP ADDRESS 10.4.128.201
SET IP NETMASK 255.255.255.0
SET IP FRAMING NONE
SET IP PROPAGATE ON
SET IP COST 1
SET IP RIP RECEIVE V1
SET IP RIP UPDATE OFF
SET IP RIP VERSION 1
SET IP ROUTE DEST 10.4.128.0/24 GATEWAY 10.4.128.200 PROPAGATE ON COST 1
Kind regards
Col
- Thread starter
- #8
- Thread starter
- #9
- Status