I got my hands on a 4000 M+ router which did not have a flash chip. I purchase a 8mb flash chip and inserted into the memory bank but I get a error when i boot up. Here is my console config: It seems to recognize the module. There is a IOS image loaded already on the flash. I can't reflash the router because i can't assign a ip address also I think the 4000 does not support xmodem transfer. I am able to get into Router(boot)# Could I load the IOS from here? Any steps i should do, thanks.
System Bootstrap, Version 4.14(7), SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
4000 processor with 32768 Kbytes of main memory
Note: A random default MAC address of 0000.0c00.0d88 has been chosen.
Ensure that this address is unique, or specify MAC
addresses on commands (such as 'novell routing')
that allow the use of this address as a default.Flash: invalid chip id 0x101
unable to configure flash for erase or write.
Flash chips recognized by system :
Code Chip-Sz Cmd-grp Chip-name
89B4 0x20000 1 INTEL 28F010
89BD 0x40000 1 INTEL 28F020
01A7 0x20000 1 AMD 28F010
012A 0x40000 1 AMD 28F020
012A 0x40000 1 AMD 28F020
1CD0 0x40000 1 M5M 28F101P
89A2 0x100000 2 INTEL 28F008SA
01A4 0x80000 3 AMD 29F0
also sh version
4000 Bootstrap Software (XX-RXBOOT), Version 9.14(7), RELEASE SOFTWARE
Patchlevel = 9.1(11)
Copyright (c) 1986-1994 by cisco Systems, Inc.
Compiled Wed 18-May-94 05:07 by chansen
System Bootstrap, Version 4.14(7), SOFTWARE
Router uptime is 4 minutes
System restarted by power-on
Running default software
cisco 4000 (68030) processor (revision 0xB0) with 32768K/4096K bytes of memory.
Processor ID 5083644
DDN X.25 software, Version 2.0, NET2 and BFE compliant.
4 Serial network interfaces.
128K bytes of non-volatile configuration memory.
8192K bytes of Flash address space sized on CPU board.
Configuration register is 0x141
System Bootstrap, Version 4.14(7), SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
4000 processor with 32768 Kbytes of main memory
Note: A random default MAC address of 0000.0c00.0d88 has been chosen.
Ensure that this address is unique, or specify MAC
addresses on commands (such as 'novell routing')
that allow the use of this address as a default.Flash: invalid chip id 0x101
unable to configure flash for erase or write.
Flash chips recognized by system :
Code Chip-Sz Cmd-grp Chip-name
89B4 0x20000 1 INTEL 28F010
89BD 0x40000 1 INTEL 28F020
01A7 0x20000 1 AMD 28F010
012A 0x40000 1 AMD 28F020
012A 0x40000 1 AMD 28F020
1CD0 0x40000 1 M5M 28F101P
89A2 0x100000 2 INTEL 28F008SA
01A4 0x80000 3 AMD 29F0
also sh version
4000 Bootstrap Software (XX-RXBOOT), Version 9.14(7), RELEASE SOFTWARE
Patchlevel = 9.1(11)
Copyright (c) 1986-1994 by cisco Systems, Inc.
Compiled Wed 18-May-94 05:07 by chansen
System Bootstrap, Version 4.14(7), SOFTWARE
Router uptime is 4 minutes
System restarted by power-on
Running default software
cisco 4000 (68030) processor (revision 0xB0) with 32768K/4096K bytes of memory.
Processor ID 5083644
DDN X.25 software, Version 2.0, NET2 and BFE compliant.
4 Serial network interfaces.
128K bytes of non-volatile configuration memory.
8192K bytes of Flash address space sized on CPU board.
Configuration register is 0x141