Cisco 2811 and IMA issues

[apepayne]

Here is my issue. I have a cisco 2811 with the IMA bundle installed. I also have 2 dual t1 controllers as well. These all come up under my show inventory. The issue is that these interfaces are not listed under show int, nor can I list any show controller t1 or show ima interface. My IOS is 12.24t2, Advanced IP Services. Is there anything special I need to enable in order to get these T1 interfaces to show up?

 

[apepayne]

here is my inventory list....

NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V01 ,

NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,

NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,

NAME: "ATM AIM 0", DESCR: "ATM AIM"
PID: AIM-ATM , VID: V01 ,


Here is the version....

XXX#show version
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(5c), RELEASE SOFTWARE (fc2)
Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 01-Aug-07 15:16 by karnagar

ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
ROM: Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(24)T2, RELEASE SOFTWARE (fc2)

XXX uptime is 11 hours, 29 minutes
System returned to ROM by reload at 08:15:48 UTC Sat Dec 26 2009
System image file is "flash:c2800nm-advipservicesk9-mz.124-24.t2.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 2811 (revision 53.51) with 774144K/12288K bytes of memory.
Processor board ID FTX0932A1YN
2 FastEthernet interfaces
4 Channelized (E1 or T1)/PRI ports
1 ATM/Voice AIM
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
250880K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102



what am I missing here????

 

[whykap]

You just need to enable the VWICS. in global config mode use the "card type" command.

Example:
card type {t1 | e1} slot [bay]