Cisco 1841 configuration issues

[afsodbj]

need help configuring a new Cisco 1841 with 2-port t1 vwic. Have the fastEthernet port configured and have set the t1 controller and configured the serial 0/0/0:0 interface for ip unnumbered and to use the ip address of the fastEthernet 0/0. I can ping the ip address of the fastEthernet interface but I can not get out to the ISP via the serial interface. Have compared the running config to previous 2610 with 1 t1 csu/dsu and all appears to match as far as the IP addressing and routes.

 

[Cluebird]

In the U.S. the D-channel for the T1 is on channel 0:23, not 0:0. Are you on a fractional T1 or a full T1?

 

[afsodbj]

I have a full T1, include is the output for the controller and the serial interface.

T1 0/0/0 is up.
Applique type is Channelized T1
Cablelength is short 266
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20040202, FPGA: 11
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 0.
Data in current interval (757 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 6 15 minute intervals):
0 Line Code Violations, 2 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 15 Unavail Secs
T1 0/0/1 is down.
Applique type is Channelized T1
Cablelength is long gain36 0db
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20040202, FPGA: 11
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 0.
Data in current interval (759 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 759 Unavail Secs
Total Data (last 6 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 5400 Unavail Secs

Serial0/0/0:0 is up, line protocol is down
Hardware is GT96K Serial
Interface is unnumbered. Using address of FastEthernet0/0 (216.177.38.105)
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 242/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 147 giants, 0 throttles
150 input errors, 150 CRC, 3 frame, 2 overrun, 0 ignored, 40 abort
603 packets output, 15001 bytes, 0 underruns
0 output errors, 0 collisions, 11 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
Timeslot(s) Used:24, SCC: 0, Transmitter delay is 0 flags

 

[afsodbj]

A configuration setting on the T1 controller appears to be the cause of the problem;

the setting for channel group should have been:

channel-group 0 timeslots 1-24 speed 64