Cisco 1750 router 4

[mcraul]

My company just bought a cisco 1750 router for their T1 connection from an auction. It looks like the router has been wiped of its firmware. When I connect to the router via serial port I get this

System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C1700 platform with 16384 Kbytes of main memory

device does not contain a valid magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
í
System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C1700 platform with 16384 Kbytes of main memory

device does not contain a valid magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"

System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C1700 platform with 16384 Kbytes of main memory

rommon 1 >


Question is how do I go about loading in the firmware? I did download the Cisco Configmaker and tried to update using that but it failed to even connect. Is there a tutorial to help me with this and also were I can get the IOS software for the router.
Thanks in advanced!

 

[mcraul]

ok i got to the ip address config part so i ran this command

and get this

Router(config)#int s0
^
% Invalid input detected at '^' marker.

ok for kicks i did this


Router(config)#ip address my.ip

and got the same error?

am i missing something??

thanks!!

 

[mcraul]

Ok this is wierd when i enter the letter s it inputs a ^ for some reason

 

[burtsbees]

Are you consoled in? Do a
router>sh ip int bri

Burt

 

[mcraul]

This is super fustrating but im learning

I cant seem to get into the router(config-if) prompt

I keep getting that invalid input error still

any ideas?

Thanks!

 

[mcraul]

Yeah im consoled in using hyperterm

 

[mcraul]

doing a

Router>sh ip int bri

I get this

Interface IP-Address OK? Method Status Prot
ocol
FastEthernet0 unassigned YES TFTP administratively down down

 

[mcraul]

I just cant seem to get past this one hurdle. just dosent let me get into router(config-if) prompt no matter what i do.

 

[burtsbees]

router(config)#int fa0

Try that.

Burt

 

[mcraul]

ok i got it!
what i did was do a

Router(config)#int fa0

and i got the config-if prompt

so next question what IP do i assign the interface? a private one or the one the ISP gave us for our T1?

Is there a tutorial somewhere i can read up on to configure this to our small network of 4 computers?

I do have the manual how to intall the router. Now from what I understand the ISP installed a CSUDSU and ran an ethernet out of it. now on the back of my router I have a T1/CSUDSU port in slot 2 of my 1750 router. Do i run the ethernet from the CSDSU to that port and then an ethernet to my hub/switch?

sorry for so many questions!

 

[mcraul]

would using the Cisco COnfig maker help me out with this?

 

[burtsbees]

Post a sh int and sh controllers, as well as sh ver. I'm not seeing (and perhaps neither is the router) a serial interface (WIC-1DSU-T1)...
The fa0 gets a private IP address, and you'll NAT everything to a public IP address. But the router needs to know about the serial interface first! You may need a better image..

Burt

 

[mcraul]

ok here is that result

Router>enable
Password:
Router#sh int
FastEthernet0 is up, line protocol is down
Hardware is PQUICC_FEC, address is 0004.2722.afd3 (bia 0004.2722.afd3)
Internet address is 63.131.66.10/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 243/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Unknown duplex, Unknown Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:07, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
7 packets output, 420 bytes, 0 underruns
7 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
7 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial0 is administratively down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=down DSR=up DTR=down RTS=down CTS=down



Now the firmware i installed was this one

c1700-y-mz.121-27b.bin

I had a this version c1700-k9o3sy7-mz.122-11.T10(2).bin but when I installed it it was bigger than my flash memory.

 

[mcraul]

bump

 

[burtsbees]

Kind of weird sh int shows it, but not sh ip int brief...I'll have to look into this...

Burt

 

[mcraul]

new updated one. I was setting up dhcp and stuff

chromacars#sh int
FastEthernet0 is up, line protocol is down
Hardware is PQUICC_FEC, address is 0004.2722.afd3 (bia 0004.2722.afd3)
Internet address is 63.131.xxx.xxx/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 128/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
282 packets output, 17286 bytes, 0 underruns
283 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
283 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Interface is unnumbered. Using address of FastEthernet0 (63.131.xxx.xxx)
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=down DSR=up DTR=up RTS=up CTS=down


SO I think I have everything setup right now see the show running-config

chromacars#show running-config
Building configuration...

Current configuration : 1057 bytes
!
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname chromacars
!
enable secret 5 xxxxxx
enable password xxxxx
!
!
!
!
!
memory-size iomem 25
ip subnet-zero
ip name-server 64.65.xxx.xxx
no ip dhcp conflict logging
ip dhcp excluded-address 192.168.0.0 192.168.255.255
ip dhcp excluded-address 192.168.0.1
!
ip dhcp pool chromacars
dns-server 64.65.xxx.xxx 64.65.xxx.xxx
default-router 63.131.xxx.xxx
domain-name mydomain.net
netbios-node-type h-node
lease infinite
!
!
!
!
interface Serial0
ip unnumbered FastEthernet0
!
interface FastEthernet0
ip address 63.131.xxx.xxx 255.255.255.0
speed auto
half-duplex
!
router igrp 1
redistribute connected
network 63.0.0.0
!
ip classless
no ip http server
!
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
snmp-server community office RO
!
line con 0
password xxxx
login
line aux 0
line vty 0 4
password xxxxx
login
!
no scheduler allocate
end


Now the T1 is connected thru an T1/CSUDUS wic card and the middle light is on "al" but I guess the light "cd" is suppose to be green showing that it sees the T1 is that right?

THANKS

 

[mcraul]

Ok I finally got the router to the cisco configmaker and it pings it fine. Now a couple quetions
what ip address should i assign to the WIC T1 interface?
and the ethernet interface? should the share the same static ip my ISP gave me?

THis is what I have now as my IOS config

!
service timestamps debug uptime
service timestamps log uptime
service password-encryption
no service tcp-small-servers
no service udp-small-servers
!
hostname Cisco1750
!
enable secret xxxx
!
ip name-server 64.65.xxx.xxx
!
ip subnet-zero
ip domain-lookup
ip routing
!
interface FastEthernet 0
no description
no ip address
shutdown
!
interface Serial 0
no shutdown
description connected to Internet
service-module t1 clock source line
service-module t1 data-coding normal
service-module t1 remote-loopback full
service-module t1 framing esf
service-module t1 linecode b8zs
service-module t1 lbo none
service-module t1 remote-alarm-enable
ip address 64.65.xxx.xxx 255.255.255.252
ip nat outside
encapsulation hdlc
!
! Access Control List 1
!
no access-list 1
access-list 1 deny any
!
! Dynamic NAT
!
ip nat translation timeout 86400
ip nat translation tcp-timeout 86400
ip nat translation udp-timeout 300
ip nat translation dns-timeout 60
ip nat translation finrst-timeout 60
ip nat inside source list 1 interface Serial 0 overload
!
router rip
version 2
passive-interface Serial 0
no auto-summary
!
!
ip classless
!
! IP Static Routes
ip route 0.0.0.0 0.0.0.0 Serial 0
no ip http server
snmp-server community public RO
snmp-server location Office
snmp-server contact Raul ,support@xxxx.com
banner motd #Welcome to xxxxx#
!
line console 0
exec-timeout 0 0
password xxxx
login
!
line vty 0 1
password xxxx
login
!
end


when I try to deliver this config to the router using the tool in config maker I get an error message

IM SOOO CLOSE to configuring this thing!

Thanks

 

[mcraul]

Ok I got it now that I am able to ping the router from the outside and can even go to the routers Apache screen. But I cant seem to route out with in the router. So I'm close!! Any more ideas would be great. I'll continue to play with it


Thanks

 

[burtsbees]

Post a sh run again

Burt

 

[mcraul]

chromacars#sh run
Building configuration...

Current configuration : 691 bytes
!
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname chromacars
!
enable secret 5 $1$E20M$byJyVavHcKNqqqIg74d9R/
enable password xxx
!
!
!
!
!
memory-size iomem 25
ip subnet-zero
!
!
!
interface FastEthernet0
ip address 63.131.xxx.xxx 255.255.255.0
speed auto
half-duplex
!
router igrp 1
redistribute connected
network 63.0.0.0
!
ip classless
no ip http server
!
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
snmp-server community office RO
!
line con 0
password xxxx
login
line aux 0
line vty 0 4
password xxxx
login
interface FastEthernet0
ip address 63.131.xxx.xxx 255.255.255.0
speed auto
half-duplex
!
router igrp 1
redistribute connected
network 63.0.0.0
!
ip classless
no ip http server
!
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
snmp-server community office RO
!
line con 0
password chroma1
login
line aux 0
line vty 0 4
password xxxx
login

 

[mcraul]

im not sure what happend but now I cant ping the router anymore