CHID error when creating trunks

[bazzieb]

Hi There

I have created a new route and when I try to add trunks to it I keep getting a CHID error:
SCH3162
In LD 14 a duplicate CHID has been entered. This CHID already exists.

Severity: Info

How do I see which channel ID I can use for these trunks?

Kind Regards
BazzieB

 

[KCFLHRC]

What type of route did you build? Post it here

 

[bazzieb]

Hi KCFLHRC

I created a SIP Route:
REQ: prt
TYPE: rdb
CUST 0
ROUT 65

TYPE RDB
CUST 00
ROUT 65
DES SIP_ASTERISK
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK YES
ZONE 00002
PCID SIP
CRID NO
SBWM NO
NODE 1000
DTRK NO
ISDN YES
MODE ISLD
DCH 60
IFC SL1
PNI 00000
NCNA YES
NCRD YES
TRO NO
FALT NO
CTYP UKWN
INAC YES
ISAR NO
DAPC NO
MBXR NO
MBXOT NPA
MBXT 0
PTYP ATT
CNDP UKWN
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 10019
TCPP NO
PII NO
AUXP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
STYP SDAT
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 10019 65
ATRR NO
TRRL NO
SGRP 0
ARDN NO
CTBL 0
AACR NO

When I try adding trunks to this route it gives me the channel ID error. I pretty much copied a SIP route I already had.

Kind regards
BazzieB

 

[bazzieb]

Hi KCFLHRC

I have managed to find my problem, I was using DCH 60, which already had 279 trunks, instead of DCH 65 which is the new one I created.

Kind Regards
BazzieB

 

[bazzieb]

Ok, so I had an issue, I copied one of the SIP DCH's that were already there, but when I added trunks to it, it seems to have conflicted with an existing SIP route. I started receiving the following error which I don't really understand:

PRI227 VIRTUAL DCH: 65 DATA: 00000002

PRI241 VIRTUAL DCH: 60 DATA: 000000EC
!
>err pri241

>

PRI0241
Protocol Error: No response from far end to this PRI call. Output data:
DCH: x DATA: y . Where: x = D-channel number and y = B-channel number.
Report problem if condition persists.
Severity: Critical

Hopefully someone can assist.

After I deleted the virtual trunks, and rebooted the NRS everything came back up.

Kind regards
BazzieB

 

[357951258]

you cannot build 2 dch for sip and h323 routes same system
thats your problem