CDR Format

[dabble]

I have an OPT 11C at 4.5.

I have turned on all the CDR prompts for all the routes, changed FCDR to NEW, enabled CDR in LD 15.

Below is a CDR record that I am getting

N 049 00 A053 021 4638 08/19 09:56:42 00:00:36 .0
&7057280364XXXXXX 000 000
&00 :07 000 01 2

My question is: The part that is A053 021, I believe should be coming out as A053021 - without the space.

I know that this is the route (53) and the member (21).

How can I get rid of the extra space?

Thanks.

 

[GHTROUT]

What if FCDR is not NEW?

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[dabble]

Even if FCDR is set to OLD, the result is the same - the space is there.

 

[Nicolas92]

Something about that on Nortel website:


Symptom:
CDR is not working properly.
Experiencing Call Detail Recording (CDR) format issues.
CDR lines are not complete at times.
CDR lines output a few lines then pause and output the rest.

Cause:
Site has three Teletype (TTY) ports configured for CDR but only one is being used.

Problem Resolution

Fix:
Remove all unused TTY ports for CDR.

 

[dabble]

Interesting.
I did a print of TTY devices, but only one of them seems to be defined as CDR port.


ADAN TTY 0
TTY_TYPE SDI
CAB 00
CARD 00
PORT 0
DES ENTERPRISEI
FLOW NO
USER MTC SCH BUG
TTYLOG 0
BANR YES
ADAN TTY 1
TTY_TYPE SDI
CAB 00
CARD 00
PORT 1
DES CDR
BPS 9600
BITL 8
STOP 1
PARY NONE
FLOW NO
USER CTY
ADAN TTY 2
TTY_TYPE SDI
CAB 00
CARD 00
PORT 2
DES ONSITE1200
BPS 1200
BITL 8
STOP 1
PARY NONE
FLOW NO
USER MTC SCH BUG
TTYLOG 0
BANR YES
ADAN TTY 3
TTY_TYPE SDI
CAB 01 FIBR
DES custdialup
FLOW NO
USER MTC SCH BUG
TTYLOG 66
BANR NO

REQ

 

[Firebird Scrambler]

What are your CDR settings in LD 15?.

I usually prefer to use OTM Data buffering and Access (if you have it?) via Ethernet access and I can just leave it running as all data is outputted into a file within the OTM site folder called detail1.img.

I then use this along with a free utility called CDR Import.xls.

All the best

Firebird Scrambler
Meridian Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[dabble]

Here is my CDR settings in LD 15


REQ: prt
TYPE: cdr
TYPE CDR_DATA
CUST 0

TYPE CDR_DATA
CUST 00
CDR YES
IMPH NO
OMPH NO
AXID YES
TRCR YES
CDPR YES
ECDR NO
BDI NO
PORT 1
BCAP NO
CHLN 0
FCAF NO

 

[Firebird Scrambler]

I tend to use the following settings below.

CDR_DATA
CDR YES
IMPH NO
OMPH NO
AXID YES
TRCR YES
CDPR YES
ECDR YES
BDI YES
OTCR YES
PORT (If using a serial port)
CNI DGTS
BCAP NO
CHLN 4
FCAF NO

All the best

Firebird Scrambler
Meridian Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[dabble]

OK Thanks. I'll change those two settings and see what happens.