Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

CBCT PRI Error (NI2) - ERR9016 00000108 NON PROVISION

Status
Not open for further replies.

Pbxpoweruser

IS-IT--Management
Jul 16, 2007
239
CA
Hi Everyone I have a new CBCI PRI (NI2) and I am unable to terminate an inbound DID call. The outbound calls work perfectly however. Does anyone see anything potentially wrong? A point of contention with the carrier is that I am receiving 4 digits from the Central Office and my numbering plan is 7 digits. I am using IDC to point the 4 digits received from the CO to the 7 digit telephone. Any thoughts?

DCH 64 UIPE_IMSG CC_SETUP_IND REF 00004081 CH 64 1 TOD 13:07:36 CK 48F63D7B
CALLED #:1350 NUM PLAN: UNKNOWN TON: UNKNOWN
CALLING #:XXXXXXXXXX NUM PLAN: E164 TON: NATL

ERR9016 00000108 NON PROVISION

DCH 64 UIPE_OMSG CC_REJECT_REQ REF 0000C081 CH 0 TOD 13:07:36 CK 48F63D7B
CAUSE: #50 - REQ FACILITYNOT SUBSCRIBED

CBCT Master Route programming

TYPE RDB
CUST 00
ROUT 264
DES ROGERS_TEST
TKTP CBCT
NPID_TBL_NUM 0
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
IPUB 0
SBN NO
PNI 00001
SVRT 200
209
NCRD YES
CHTY BCH
MBXR NO
MBXOT NPA
MBXT 0
CNDP UKWN
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
ACOD 1000064
TCPP NO
TARG
CLEN 1
BILN NO
OABS
ICIS NO
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
DRNG NO

Incoming DID Route

TYPE RDB
CUST 00
ROUT 200
DES DID
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR YES
RTN 264
SRVC 0
IEC ---
MAX 23
NCOS 0
SBN NO
PNI 00001
NCNA YES
NCRD YES
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL VOD
PTYP PRI
CNDP LOCL
AUTO NO
DNIS NO
DCDR NO
ICOG ICT
STEP
ACOD 1000200
PII NO
AUXP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096


PAGE 002

RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

Outgoing Route

TYPE RDB
CUST 00
ROUT 209
DES OUTGOING
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR YES
RTN 264
SRVC 0
IEC ---
MAX 23
NCOS 4
SBN NO
PNI 00001
NCNA YES
NCRD YES
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL VOD
PTYP PRI
CNDP UKWN
AUTO NO
DCDR NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 1000209
TCPP NO
TARG 01
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
OOD 3
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096



PAGE 002

IENB 5
TFD 0
LEXT 100
VGD 6
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA YES
OAN YES
OPD YES
CDRX NO
NATL YES
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

D Channel Programming
ADAN DCH 64
CTYP MSDL
MG_CARD 000 1 01
PORT 1
DES TEST
USR PRI
DCHL 64
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID 36
RCAP NCT COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
 
Is the DCNO # you are entering the conversion in the same as in the route, ie 1?
 
Yes I am using DCNO 1 which contains the following:


DCNO 1
IDGT CDGT
1350 7482540
 
The LDN entry must be the same length as the number of received digits from the C.O.
 
Hi,
I just checked and there was no LDN programmed as this is a new system. I programmed one but still get the same issue.
 
Finally found the issue. The IPUB prompt on the CBCT master router needed to point to the incoming service route of 209. Once that was changes everything worked perfectly.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top