CBCT PRI Error (NI2) - ERR9016 00000108 NON PROVISION

[Pbxpoweruser]

Hi Everyone I have a new CBCI PRI (NI2) and I am unable to terminate an inbound DID call. The outbound calls work perfectly however. Does anyone see anything potentially wrong? A point of contention with the carrier is that I am receiving 4 digits from the Central Office and my numbering plan is 7 digits. I am using IDC to point the 4 digits received from the CO to the 7 digit telephone. Any thoughts?

DCH 64 UIPE_IMSG CC_SETUP_IND REF 00004081 CH 64 1 TOD 13:07:36 CK 48F63D7B
CALLED #:1350 NUM PLAN: UNKNOWN TON: UNKNOWN
CALLING #:XXXXXXXXXX NUM PLAN: E164 TON: NATL

ERR9016 00000108 NON PROVISION

DCH 64 UIPE_OMSG CC_REJECT_REQ REF 0000C081 CH 0 TOD 13:07:36 CK 48F63D7B
CAUSE: #50 - REQ FACILITYNOT SUBSCRIBED

CBCT Master Route programming

TYPE RDB
CUST 00
ROUT 264
DES ROGERS_TEST
TKTP CBCT
NPID_TBL_NUM 0
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
IPUB 0
SBN NO
PNI 00001
SVRT 200
209
NCRD YES
CHTY BCH
MBXR NO
MBXOT NPA
MBXT 0
CNDP UKWN
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
ACOD 1000064
TCPP NO
TARG
CLEN 1
BILN NO
OABS
ICIS NO
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
DRNG NO

Incoming DID Route

TYPE RDB
CUST 00
ROUT 200
DES DID
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR YES
RTN 264
SRVC 0
IEC ---
MAX 23
NCOS 0
SBN NO
PNI 00001
NCNA YES
NCRD YES
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL VOD
PTYP PRI
CNDP LOCL
AUTO NO
DNIS NO
DCDR NO
ICOG ICT
STEP
ACOD 1000200
PII NO
AUXP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096


PAGE 002

RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

Outgoing Route

TYPE RDB
CUST 00
ROUT 209
DES OUTGOING
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR YES
RTN 264
SRVC 0
IEC ---
MAX 23
NCOS 4
SBN NO
PNI 00001
NCNA YES
NCRD YES
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL VOD
PTYP PRI
CNDP UKWN
AUTO NO
DCDR NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 1000209
TCPP NO
TARG 01
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
OOD 3
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096



PAGE 002

IENB 5
TFD 0
LEXT 100
VGD 6
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA YES
OAN YES
OPD YES
CDRX NO
NATL YES
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

D Channel Programming
ADAN DCH 64
CTYP MSDL
MG_CARD 000 1 01
PORT 1
DES TEST
USR PRI
DCHL 64
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID 36
RCAP NCT COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

 

[trvlr1]

Is the DCNO # you are entering the conversion in the same as in the route, ie 1?

 

[Pbxpoweruser]

Yes I am using DCNO 1 which contains the following:


DCNO 1
IDGT CDGT
1350 7482540

 

[KCFLHRC]

What does your LDN Data Block look like?

 

[KCFLHRC]

The LDN entry must be the same length as the number of received digits from the C.O.

 

[Pbxpoweruser]

Hi,
I just checked and there was no LDN programmed as this is a new system. I programmed one but still get the same issue.

 

[Pbxpoweruser]

Finally found the issue. The IPUB prompt on the CBCT master router needed to point to the incoming service route of 209. Once that was changes everything worked perfectly.