Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Can't perform an EDD in ld 43

Status
Not open for further replies.
camaro67

camaro67

Technical User
Mar 3, 2005
160
US
we have an op[tion 11c rel.23 ( i know you don't have to say it....upgrade) when i try to do a backup it will start but will never finish i also have alot of bug codes....

% BUG6347 ssDrv: Logical block mapping is invalid. pDrv = 0x2009125c, task = tR
pt, tid =
% 0x202ee448
% block = 45, caddr = 008E
%
% BUG6347 ssDrv: Logical block mapping is invalid. pDrv = 0x2009125c, task = tR
pt, tid =
% 0x202ee448
% block = 1, caddr = 008E
%
% BUG6347 ssDrv: Logical block mapping is invalid. pDrv = 0x2009125c, task = tE
vtColl, ti
% d = 0x202cb460
% block = 5244, caddr = 008E
%
 
Sort by date Sort by votes
If you can get into PDT, check those addresses for corruption.
But, Get ready to rebuild that system. I hope you have a good backup on a PCMCIA drive or backup on remote disk some where. If you don't, print out and capture the whole system. Use ghtrout's conversion tools to make a database that you can restore to your newly reloaded PBX. Be sure (if you have to...) to erase the memory daughter board of all data. Run the "utility" tool when reloading and run "diagnostics". Good luck.

DocVic
Dedicated to Nortel Products till the end.
Need help?
 
Upvote 0 Downvote
thanks Doc I'm not to familier with PDT, how do i access PDT? i do have a backup disk
 
Upvote 0 Downvote
CTRL + P + D + T keys I guess with its own Password...

Go For It Even If It's Impossible !
 
Upvote 0 Downvote
Oh boy! That EDD CLR command can be very dangerous. Be ready to reload this machine if it doesn't come back to life.

If you don't know PDT, don't even attempt to play. You might want to have your local vendor come over (with spare parts and after hours...) for a visit and diagnose what is going on with your system. Sounds like a memory error or the SSC is failing. Being prepared with some spare parts is the only way to handle this, and some experience isn't to bad either.

DocVic
Dedicated to Nortel Products till the end.
Need help?
 
Upvote 0 Downvote
As per my little experience, EDD Failure is one of the most serious errors CS1000 can have...

Go For It Even If It's Impossible !
 
Upvote 0 Downvote
What I'd do is to log into LD 43 and do a "DAT". We need to see what databases are present. My guess is that you only have the internal backup preset on the SSC card.

The database might be a few Months old, but I'd get a backup done onto my computer by going into LD 143 from a serial port i.e. TTY 0 with X Modem and do a XBK to receive that copy.

It's better to have any backup as long as it's a good copy. I did this recently on a release 24.25 opt 11c.



All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Upvote 0 Downvote
when you do the DAT you should see somethng like this:


.dat
DATABASE ISSUE DATE(d/m/y)/TIME SIZE(recs) SEQNO
Main 300 02/12/2010 at 05:01:06 90 3225
Secondary 300 01/12/2010 at 05:01:02 90 3224
IntBackup 300 02/12/2010 at 05:01:06 90 3225
PCMCIA database not accessible.
Current external backup is on PCMCIA drive B


Thanks,

Buddy

Linked in Profile
 
Upvote 0 Downvote
thanks to everyone for your response.This is what i have when i do ld 43 DAT >ld 43 I another SSC card on the way we recently had to replace the original one.
EDD000


.dat
DATABASE ISSUE DATE(d/m/y)/TIME SIZE(recs) SEQNO
Main database not accessible.
Secondary database not accessible.
IntBackup 2335 29/06/2007 at 01:06:44 93 3103
PCMCIA database not accessible.
Current external backup is on PCMCIA drive B

 
Upvote 0 Downvote
That is the same problem I had!. Please do the XBK first!. However, I do realise that the internal backup stored on the SSC card is dated 29 June 2007!.

Also, your SSC CARD ISN'T THE PROBLEM!. The daughterboard is corrupted and needs to be reformatted and your V23.35 software reloaded back onto it, before you restore your image that is still on the SSC card.

The instructions on the daughterboard restore are in my guide.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Upvote 0 Downvote
ok how do i reformat the daughter board? do i reload the daughterboard using the XBK file?
 
Upvote 0 Downvote
Firebirdscrambler how do i get to your guide? I need all the help i can get at this.
 
Upvote 0 Downvote
Hey Camaro, if you have never performed a reload, you should get some help with it. It takes a few experienced steps to get one done. Your questions tell me you don't have that experience. Call your local Nortel vendor and ask what they charge to get this done. And ask if they have the tools to get this done. It should take no more then 2 hours OT, and don't throw a fit, cuz most of the time he's just gonna be watching the screen loading.
Firebird is right. If you already replaced one SSC, and the problem came back, it's your daughter board.
Eh, I kinda mentioned all this in my first post...

DocVic
Dedicated to Nortel Products till the end.
Need help?
 
Upvote 0 Downvote
As was already posted the other day.

ghtrout.com - This website is for sale! - ghtrout Resources and Information.

This website is for sale! ghtrout.com is your first and best source for all of the information you’re looking for. From general topics to more of what you would expect to find here, ghtrout.com has it all. We hope you find what you are searching for!
www.ghtrout.com www.ghtrout.com

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

SherWat
  • Locked
  • Question
ENTC in LD 80 Results Decipher
Replies
0
Views
93
SherWat
SherWat
lastation4
  • Locked
  • Question
Can't get T1 DCH to establish
Replies
6
Views
236
lastation4
lastation4
shan_ali
  • Locked
  • Question
NEED SIMPLE LD OPERATION IN PDF PLE
Replies
2
Views
138
Firebird Scrambler
Firebird Scrambler
HollTel
  • Locked
  • Solved
Nortel CS1000 can't login?
Replies
1
Views
120
bignose21
bignose21
cheikhdtn
  • Locked
  • Question
Ld 95
Replies
1
Views
102
bignose21
bignose21

Part and Inventory Search

Sponsor

Back
Top