Can't Dial a DSC from console

[Slider55]

I can't dial a DSC of (6) from my console. I get a busy if I do. There are two other DSC's that work fine from it.

I have all DSC's rli's the same. I can dial the ACOD of the route and then the dsc number and call goes through fine. I can dial the DSC off of any other analog or digital set and it goes through fine. the ncos of the console and the frl are the same (7). The routes on the "good" dsc's are tie and the "bad" one is a DID route.
TGAR and TARG are turned off on this switch.

 

[59Deano]

What is your 'FLEN' on your DSC's? Set the Flen to the length of your DSC, not '0'.

 

[Slider55]

Ok, I just tried that and still got the busy...I set the Flen to 4 and the console goes to a busy just as soon as the 6 is pressed...
This has got me scratch'n

 

[1norteltech]

Your original post says "I have all DSC's rli's the same",
but then it says they are using different routes. Can you post the dsc and the rli?

 

[Slider55]

Yes you are correct..I did say that, I should have said not including the routes. They are pointing to different routes. Stdby and I'll get that info for ya...

 

[Slider55]

REQ prt
CUST 0
FEAT rlb
RLI 22


RLI 22
ENTR 0
LTER NO
ROUT 4
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO
ISET 0
NALT 5
MFRL 0
OVLL 0



REQ prt
CUST 0
FEAT rlb
rLI 18

RLI 18
ENTR 0
LTER NO
ROUT 8
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO
ISET 0
NALT 5
MFRL 0
OVLL 0





REQ prt
CUST 0
FEAT rlb
RLI 19

RLI 19
ENTR 0
LTER NO
ROUT 9
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO

ENTR 1
LTER NO
ROUT 0
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP YES
FRL 6
DMI 3
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO

ISET 1
NALT 5
MFRL 0
OVLL 0

>ld 90

ESN000



MEM AVAIL: (U/P): 6371858 USED U P: 375679 215662 TOT: 6963199

>ld 87

REQ prt
CUST 0
FEAT cdp
TYPE dsc
DSC 6

DSC 6
FLEN 4
DSP LSC
RLI 22
NPA
NXX




REQ prt
CUST cdp

CUST 0
FEAT cdp
TYPE dsc
DSC 1

DSC 1
FLEN 0
DSP LSC
RLI 18
NPA
NXX


REQ prt
CUST 0
FEAT cdp
TYPE dsc
DSC 8200

DSC 8200
FLEN 0
DSP LSC
RLI 19
NPA
NXX




>ld 21

PT1000



REQ: prt
TYPE: rdb
CUST 0
ROUT 4
TYPE RDB
CUST 00
ROUT 4
DES CISCO
TKTP DID

M911_ANI NO

M911_TONE NO

NPID_TBL_NUM 0

SAT NO

RCLS EXT

VTRK NO

DTRK YES

BRIP NO

DGTP PRI

ISDN YES

MODE PRA

IFC NI2

CBCR NO

NCOS 0

SBN NO

PNI 00000

NCNA YES

NCRD YES

CHTY BCH

CPFXS YES

CPUB OFF

DAPC NO

BCOT 0

INTC NO

DSEL 3VCE

PTYP PRI

AUTO NO

DNIS NO

DCDR NO

ICOG IAO

RANX NO

SRCH RRB

TRMB NO

STEP

ACOD 7004

TCPP NO

PII NO

TARG

CLEN 1

BILN NO

OABS

INST

IDC NO

DCNO 0 *

NDNO 0

DEXT NO

ICIS YES

TIMR ICF 512

OGF 512

EOD 13952

NRD 10112

DDL 70

ODT 4096

RGV 640

FLH 510

GRD 896

SFB 3

NBS 2048





PAGE 002



NBL 4096



IENB 5

VSS 0

VGD 6

DRNG NO

CDR NO

VRAT NO

MUS NO

RACD NO

EQAR NO

FRL 0 0

FRL 1 0

FRL 2 0

FRL 3 0

FRL 4 0

FRL 5 0

FRL 6 0

FRL 7 0

OHQ NO

OHQT 00

TDET NO

TTBL 0

ATAN NO

PLEV 2

MCTS NO

ALRM NO

ART 0

SGRP 0

AACR NO



REQ: prt

TYPE: rdb

CUST 0

ROUT 8



TYPE RDB

CUST 00

ROUT 8

DES PRI-GRD-CRN

TKTP TIE

NPID_TBL_NUM 0

ESN NO

CNVT NO

SAT NO

RCLS EXT

VTRK NO

DTRK YES

BRIP NO

DGTP PRI

ISDN YES

MODE PRA

IFC SL1

PNI 00001

NCNA YES

NCRD YES

TRO NO

CHTY BCH

CTYP UKWN

INAC NO

ISAR NO

DAPC NO

DSEL 3VCE

PTYP PRI

AUTO NO

DNIS NO

DCDR NO

ICOG IAO

SRCH RRB

TRMB NO

STEP

ACOD 7038

TCPP NO

TARG 01

CLEN 1

BILN NO

OABS

INST

IDC NO

DCNO 0 *

NDNO 0

DEXT NO

ANTK

SIGO STD

ICIS YES

TIMR ICF 512

OGF 512

EOD 13952

NRD 10112

DDL 70

ODT 4096

RGV 640

GRD 896

SFB 3

NBS 2048

NBL 4096



IENB 5

TFD 0





PAGE 002



VSS 0

VGD 6

DRNG YES

NDRI 00

CDR YES

INC YES

LAST NO

QREC NO

OAL YES

AIA YES

OAN NO

OPD NO

CDRX NO

NATL YES

VRAT NO

MUS YES

MRT 11

RACD NO

EQAR NO

FRL 0 0

FRL 1 0

FRL 2 0

FRL 3 0

FRL 4 0

FRL 5 0

FRL 6 0

FRL 7 0

OHQ NO

OHQT 00

CBQ NO

AUTH NO

TDET NO

TTBL 0

ATAN NO

PLEV 2

ALRM NO

ART 0

SGRP 0

AACR NO



REQ: prt

TYPE: rdb

CUST 0

ROUT 9



TYPE RDB

CUST 00

ROUT 9

DES PRI-SALES

TKTP TIE

NPID_TBL_NUM 0

ESN NO

CNVT NO

SAT NO

RCLS EXT

VTRK NO

DTRK YES

BRIP NO

DGTP PRI

ISDN YES

MODE PRA

IFC SL1

PNI 00001

NCNA YES

NCRD YES

TRO YES

CHTY BCH

CTYP UKWN

INAC NO

ISAR NO

DAPC NO

DSEL 3VCE

PTYP PRI

AUTO NO

DNIS NO

DCDR NO

ICOG IAO

SRCH LIN

TRMB NO

STEP

ACOD 7039

TCPP NO

TARG

CLEN 1

BILN NO

OABS

INST

IDC NO

DCNO 0 *

NDNO 0

DEXT NO

ANTK

SIGO STD

ICIS YES

TIMR ICF 512

OGF 512

EOD 13952

NRD 10112

DDL 70

ODT 4096

RGV 640

GRD 896

SFB 3

NBS 2048

NBL 4096



IENB 5

TFD 0





PAGE 002



VSS 0

VGD 6

DRNG YES

NDRI 00

CDR YES

INC YES

LAST NO

QREC NO

OAL YES

AIA YES

OAN NO

OPD NO

CDRX NO

NATL YES

VRAT NO

MUS YES

MRT 11

RACD NO

EQAR NO

FRL 0 0

FRL 1 0

FRL 2 0

FRL 3 0

FRL 4 0

FRL 5 0

FRL 6 0

FRL 7 0

OHQ NO

OHQT 00

CBQ NO

AUTH NO

TDET NO

TTBL 0

ATAN NO

PLEV 2

ALRM NO

ART 0

SGRP 0

AACR NO

 

[Slider55]

I have built an ac2 code of 20 and an spn of 6 to the same rli 22 DID route 4 and the call goes through off of the console using ac2 (20 6400). Could it be that the console just doesn't like the cdp going to a DID route and likes the TIE better. I'm going to try building a TIE route on one of the channels for a test.

 

[Slider55]

The switch will not let me build a TIE route, it won't go past the CBCR prompt unless I answer YES. If I do that then it wants a master ISA route number. I've never messed with building those. Any Idea's what I'm doing wrong??

 

[1norteltech]

I was thinking dsc's use tie only, but you said other phones are able to dial it ok. Sorry, but I'm at a loss. I have no consoles here, so I don't know the programming. Maybe someone else has the answer. Couldn't hurt to post the console programming.

 

[Slider55]

This t1 is going over to a Cisco Call Manager. I was hoping someone out there would be up for trying to help solve this one. I'm really at a loss for support on this and in dire need. Right now we are transfering the caller to a digital extension so they can transfer the caller to the cdp number. I have tried programing a test tie route and failed, for some reason it wants the route to be an ISA route and I don't understand why. I'm looking for a way to do this as Q
SIG as well, if anyone has any documentation for a compatable setup for Nortel/Cisco, I'd sure appreciate it. Does anyone have any other suggestions...besides melting it down.

 

[Slider55]

I'll post the console programing in the morning, Thank you 1norteltech and 59deano for your suggestions.

 

[GHTROUT]

Try changing the DSC to a TSC or a LSC? If that doesn't stop anything else from working, it may prove something at least.

Consoles have no programming relevant to call restriction. This is an odd one. I am wondering if this a BARS corruption issue? You might try setting the console to a "different" NCOS, just to see if that kicks anything into operation.

I've seen corruption do very odd things in BARS - nothing that made sense. Just a possibility.


[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[SL1M1]

The only thing I would suggest is changing your Route/Dchannel/Members to be QSIG/ISGF for call to and from Cisco and ForceDownload the changes to the MSDL but before you do that just change the DistantSteeringCode 'DSC' to a TrunkSteeringCode 'TSC' as already suggested

Cheers!!

 

[Slider55]

Thanks guys...I'll give that a try and let you know.

 

[RKDavis]

Cisco has doucments that tell you how to intergrate Call Mangers to Nortel Switches. Ask your Cisco vendor. The information helps with building common equipment, routes, B channesl onthe span and correct D channel information. It worked for me.