Can't delete the board ....again.. 2

[SamTool]

There is BC9, CNI85, 1 LIM.

After initial loading I initiated TLU50 on the position 1-0-30.

With some reason, it was assigned 24 t/s for this board.
The Route, Equ, and Dest were programmed also. Wihout problems.
After testing, I needed to do some cofiguration changes. Normally deleted Dest, Trunks & Rou.

But when tryed to kill the board, I got
<CNBOE:BPOS=1-0-30;
CONFIGURATION BOARD END
INDIVIDUAL STILL INITIATED ON EQU 1-0-30-00
END
<SYEDP:BPOS=1-0-30;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
001-0-30-00 48 -
END


Almost end of story.

Not possible now to assign Equ back on this board:
<ROEQI:ROU=7,TRU=1-1,EQU=1-0-30-1;
NOT ACCEPTED
EQU
NOT ALLOWED

When install new bord in LIM and search it automatically get also:
<CNHUI:LIM=1;
ORDERED
SPONTANEOUS PRINTOUT
CONFIGURATION HARDWARE UPDATE
BPOS=001-0-33
POSITION ERROR ILLOGICAL INSERTED BOARD
END


No doubt, data in DCP corrapted....

I'd very mush appreciate, if someone can briefly explane:

1. Which FILNO keeps data about trunks on board status?
2. How to find POINT with known BPOS?
3. What should be DATA for the board with and without TRU assigned? (PLEX for BC9 availible, but really no time to dig it deeply).

Or, if no time to explain, just give me, please, FILNO, POINT and DATA for this case.

As this problem is rather common one, may be some hero can put the description to FAQ area.


Thanks in advance



<CNLIP:LIM=1,DEV=YES;
LIM CONFIGURATION
LIM NUMBER 1
LIM CONTROL LIM CONTROL NUMBER OF SERVICE
SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM
A EXECUTING 0 ACTIVE
B NOT EQUIPPED
MEMORY MEMORY MEMORY SPARE
VOLUME SPARE AFTER PACKING
24575 KB 4103 KB 4103 KB

BUAR1 1926 KB BUAR2 1519 KB

DEVICE BOARDS
NUMBER OF
BPOS BOARDID INDIVIDUALS SERVICE STATE
001-0-00 57 32 ACTIVE
001-0-10 2 8 ACTIVE
001-0-11 2 8 ACTIVE
001-0-12 2 8 ACTIVE
001-0-13 2 8 ACTIVE
001-0-20 2 8 ACTIVE
001-0-21 26 3 ACTIVE
001-0-22 7 4 ACTIVE
001-0-23 69 4 ACTIVE
001-0-30 48 24 ACTIVE
001-0-33 NOT EQUIPPED
001-0-40 19 1 ACTIVE
001-0-41 29 2 ACTIVE
001-0-42 26 3 ACTIVE
001-0-43 26 3 ACTIVE
001-0-50 59 8 ACTIVE
001-0-51 31 8 ACTIVE
001-0-52 26 3 ACTIVE
001-0-53 26 3 ACTIVE
001-0-60 102 32 ACTIVE
001-0-70 59 8 ACTIVE
001-0-71 NOT EQUIPPED
001-0-72 NOT EQUIPPED
001-0-73 42 8 ACTIVE
001-1-00 48 32 ACTIVE
001-1-10 2 8 ACTIVE
001-1-11 2 8 ACTIVE
001-1-12 2 8 ACTIVE
001-1-13 2 8 ACTIVE
001-1-20 2 8 ACTIVE
001-1-21 26 3 ACTIVE
001-1-22 26 3 ACTIVE
001-1-23 26 3 ACTIVE
001-1-30 102 32 ACTIVE
001-1-40 48 32 ACTIVE
001-1-50 31 8 ACTIVE
001-1-51 NOT EQUIPPED
001-1-52 2 8 ACTIVE
001-1-53 NOT EQUIPPED
001-1-60 2 8 ACTIVE
001-1-61 2 8 ACTIVE
001-1-62 2 8 ACTIVE
001-1-63 NOT EQUIPPED
001-1-70 27 32 ACTIVE


<SCEXP;
EXTERNAL SYNC RECEIVING LINES DATA
MASTER LIM STATUS
FIRST CHOICE 1-1-00-0 SYNC RECEIVING
SECOND CHOICE NOT PRESENT
THIRD CHOICE NOT PRESENT
END

 

[fcpli]

Hi!

In your case the FILNO=1,reloff=6,point=060&&07f.
Data=00 means the bpos is not used, 01 means that you have a board there, and 02 means that it is assigned eg. with trunk.

The idea to count point when bpos is known, is simple:
Every 10-group has 32 positions = hex20. Just multiply the 10-groupvalue with 32, convert it to hex and there it is!
(for example 1-0-30 value is 3, and 3x32=96, hex60).
Every magazine has a value, too. Mag0=0, mag1=1 etc, meaning that e.g bpos x-1-30 has a value of 160 (hex) and so on.

good luck

 

[SamTool]

Fcpli,

Thanks o lot!
You have saved a day of my job!

Really thanks!