Can't connect one-x comminicator to processor ethernet .

[AlexSki]

Hi all,
I've installed MBT_5.2.1.3.6_with_media_services and CM (R015x.02.1.016.4) there. Also i have one-x communicator(6.2.10.03). but i can't connect one-x(h.323) to processor ethernet cm. What type of station do i need set in add station -? or i need only C-lan -?

Type: PROCR Target socket load: 1700

Enable Interface? y Allow H.323 Endpoints? y
Allow H.248 Gateways? y
Network Region: 1 Gatekeeper Priority: 5



IPV4 PARAMETERS
Node Name: procr
Subnet Mask: /16

display node-names ip procr
IP NODE NAMES
Name IP Address
procr 172.16.0.30

 

[kyle555]

list trace ras ip-station 1234 in emulation and see.

Got a media gateway up on it?

Need DSPs on a G430/450 or medpro cards on a G650 to get phones to register. If you got 'with media services" then there should be a VM in there named cobar that has a virtual G650 gateway in it.

You might need to build out your g650. Does list ips or list cab show anything?

And geeze, if you're trying to learn, try to get your hands on current stuff! I wouldn't teach a newbie G650 at all for the last 5 years unless they absolutely had to support legacy systems.

 

[AlexSki]

list trace station 1010 Page 1

LIST TRACE

time data

07:54:27 rcv GRQ ext 1010
endpt [172.16.0.100]:1024
switch [172.16.0.30]:1719
07:54:27 snd GCF ext 1010
endpt [172.16.0.100]:1024
switch [172.16.0.30]:1719
07:54:27 rcv RRQ ext 1010
endpt [172.16.0.100]:1024
switch [172.16.0.30]:1719
07:54:30 rcv RRQ ext 1010
endpt [172.16.0.100]:1024
switch [172.16.0.30]:1719
07:54:33 rcv RRQ ext 1010
endpt [172.16.0.100]:1024
switch [172.16.0.30]:1719
one-x 1010 don't receive answer to register from CM

list cabinet

CABINET REPORT

No Layout/ Rack/ Net Loc A B C D E
Room Floor Building Reg
1 G650 MediaS 1 1 PN 01

2 G650 1 1 PN 02

list ipserver-interface

IP SERVER INTERFACE INFORMATION

Port Pri/ Primary/ Primary/ Primary/ State Of
Ntwk Sec Secondary Secondary Secondary Serv Control Health
Num Bd Loc IP Address Host Name DHCP ID State State C P E G
---- ------ --------------- ---------------- --------- ----- ------- -------
1 1A01 172.16.0.35 172.16.0.35 ipsi-A01a OUT active 0.1.1.0

2 2A01 172.16.0.50 172.16.0.50 ipsi-A02a OUT active 0.1.1.0


I added G.650 in processing install of MBT

 

[kyle555]

Yeah, the RRQ should get a RCF if you're good or a RRJ if you're not

list conf all - are there medpros in the G650?

Maybe do a 'display events' of type 'denial' for your extension and see if/what denial event you have

 

[AlexSki]

yeah, you are right
display events

EVENTS REPORT

Event Event Event Event First Last Evnt
Type Description Data 1 Data 2 Occur Occur Cnt

2094 TCP/IP sig socket failure AC1E000C 13C5 05/27/16:26 05/27/16:28 8
2094 TCP/IP sig socket failure AC100022 13C5 05/27/16:26 05/28/01:10 33
2094 TCP/IP sig socket failure AC10001F 6B8 05/27/18:59 05/28/01:05 3
2041 IP RRJ-No DSP Resource 0 AC100064 05/28/02:47 05/28/08:20 75
Now if i can understand why (, I thought that medpro activated already, where i must to dig -?.

list configuration all

SYSTEM CONFIGURATION

Board Assigned Ports
Number Board Type Code Vintage u=unassigned t=tti p=psa

01A04 IP MEDIA PROCESSOR no board
01A05 IP MEDIA PROCESSOR no board
01A06 IP MEDIA PROCESSOR no board
01A07 IP MEDIA PROCESSOR no board
02A06 DS1 INTERFACE no board 01 02 03 04 05 06 07 08
09 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 u
01A TONE/CLOCK no board
02A TONE/CLOCK no board

isplay node-names ip
IP NODE NAMES
Name IP Address
CMM 172.16.0.31
MedSvcsMedpro1 172.16.0.40
MedSvcsMedpro2 172.16.0.41
MedSvcsMedpro3 172.16.0.42
MedSvcsMedpro4 172.16.0.43
aeserver1 172.16.0.33
default 0.0.0.0
procr 172.16.0.30
ses1 172.16.0.34
vspGateway 172.16.0.10

 

[kyle555]

Your cabinet isn't up. C.P.E.G needs to be 0.0.0.0

So, how did you get a MBT 5.2 with Cobar installed? You must have spun it up on system platform

So did you install system platform in VMware?

if so, somewhere in the NIC config in VMware you have to set something to promiscuous mode for the vswitch to be happy hearing all sorts of MACs at layer 2

 

[AlexSki]

kyle555 you are right again .Thanks .Cm did not ping G.650., I've set promiscuous mode on nic and all good.
Now one-x have registred , but i don't hear dial tone -? .Sound is ok, if i press digits . I tryid make a call between two one-x and i heared ring.
According for your advice to learn new systems. I have installed on ESXi Media Server 7.7 and CM-simplex-7(without license) but i don't see command add, change although i created privileged user.
Can i work with it without license some period -?

 

[kyle555]

First thing you do on a new CM is save translations and reset system 4. Can't remember if R7 forces you to have a license to start with. Media Server won't work without a license for itself to run the software instance. Then CM needs a license for the media server to use whatever number of channels you purchase. Avaya licenses the channels via CM and charges about the same as 1/320 of a G450 so the DSPs cost the same, you just save the space and power footprint.

Buy one of these :

https://www.ebay.com/itm/AVAYA-G350...m51ecc6712e:g:kYYAAOSwPCVX9Ahz&frcectupt=true

You won't regret it!

As far as your no dial tone problem, if your phone's regsiter and can call each other, CM thinks the medpros are up. Follow the packets.

If you go in dom0 of system platform and ifconfig you'll notice that there's a bunch of NICs. Like vSwitches, it'll have networks/vlans avpublic and avprivate. Then dom0 will have vif1.0 vif2.0, vif 2.1, etc. Those virtual interfaces are assigned to each VM Say vif2.0 and vif 2.1 would be the public and private interfaces for the second virtual machine.

System Platform uses avprivate - 172.20.10.1 for dom0, .2 for cdom, etc, to comfigure the virtual machines in the background.

Playing with tcmdump should help you follow the flow.

But, most importantly, what are you trying to learn and why? What's your background?
If you work at a company that happens to run old CM 5.2 and you want to move into the telecom department - then good work, you're on the right track. If you're trying to get a better job as an installer or designer and want some proficiency with the system, I'd strongly recommend you include SIP at every step of the way - so, System/Session Manager and Branch Session Manager/SBC and the UC applications. 10 years ago, SIP clients and phone firmware was clunky, a pain, didn't work as good and not many people were getting hands on with SIP phones because there was no practical reason. Today, a lot of people can still get by with H323, but the SIP stuff is a lot more mature in Avaya's stack and would be considered required learning each step of the way.

You know, we're not allowed posting personal contact details or anything here, but there's some nice folks here. If anonymous could login to ftp.alexski.com with upload permissions, you might be surprised at what people are willing to share

 

[AlexSki]

Thanks one more.Yeah i need to support old systems but i have desire to learn new one and try find a new job .Unfortunately i have no ftp now. If someone may help i'll be glad . Best communicate via email alexski732 domain yahoo.com and i find the way.