Cannot stop output of CDR records to terminal

[ride98red]

I cannot seem to stop the output of CDR records to my terminal. I thought I could start/stop it using LD 15 but that doesnt seem to work anymore. I dont know what I changed to make it do this but am very frustrated in making it stop. If anyone could help, please let me know. Thanks a million

 

[BobFroeh]

LD15 CDR SHOULD HAVE DONE IT??
OR YOU COULD CHANGE THE TTY TAKE OUT CTY AS ONE OF THE USERS

 

[ride98red]

OK, so heres the story. I am still trying to stop the CDR output to the terminal, however, I cannot disable the tty because I cannot disable the tty that I am logged into. (Makes sense) Let me explain what is happening as of now. Initially I needed the CDR data to be spit out to a AS/400. Got that to work. But it only spit out the data to the AS/400. Somewhere along the line, within the last week, I made a change to something that made the data spit out to the AS/400 and the terminal. So, now if I go to LD 15 and CHG the CDR_DATA I can stop the output, but it stops it to both the AS/400 and the terminal. This tells me that they are both on the same port. Is that possible? If so, can I change it so the AS/400 is on its own port receiving data by itself?
If I go to LD 17 and do a REQ=chg TYPE=ADAN ADAN=CHG TTYx and get to USER and try XCDR, it wont allow it. It does however like XTRF (Traffic) That did not help either.
When I do a stat in LD 37 this is the Output:
TTY 0 : ENBL
TTY 1 : ENBL DES: ONSITE
TTY 2 : ENBL DES: MODEM
TTY 3 : ENBL
TTY 6 : ENBL DES: ACDPRT1
TTY 7 : ENBL DES: MSR
MSI 0 : ENBL

When I do a stat in LD 42 this is the Output:
SDI 0 TTY ENBL
SDI 1 TTY ENBL DES: ONSITE
SDI 2 TTY ENBL DES: MODEM
SDI 3 TTY ENBL
SDI 6 TTY ENBL DES: ACDPRT1
SDI 7 TTY ENBL DES: MSR

I am new to Meridian, and am learning as I go (and making plenty of mistakes) I know nothing about the ports and cards in the PBX~~~> it would be nice to have some documentation. I think what needs to be done is to move the AS/400 to a different port so that the terminal and 400 are separate!
Any suggestions are very welcome! Thanks

 

[BobFroeh]

TRY LD22
REQ PRT
TYPE ADAN TTY

SHOULD COME BACK WITH USER BUG MTC CTY

CTY INDICATES CDR TO THIS TTY

THEN LD17
REQ CHG
TYPE ADAN
ADAN CHG TTY #


USER XCTY

I THINK THAT SHOULD DO IT

 

[ride98red]

Thank you very much for the advice! I will give it a try and see what happens.

 

[ride98red]

OKay, I now can start/stop the CDR output to the terminal
However, I still have the problem when I shut off the terminal, I loose the CDR output to the AS/400.
So, my next big question is, can anyone tell me the proper way to set up the CDR data to go to the AS/400?
Can I create a new port (tty) for the AS/400 to use all by itself?
In LD 17 what is PTY? I know it means Pseudo TTY and its an input/output port card type but what does it do for you?
And one last question, When I'm in LD 22 and do an ADAN PRT, all that is returned is a blank <cr>, nothing else, just totally blank?

Thanks for the help!