Cannot dial NXX over PRI

[old61]

I have a CS1000 V5.5 and can dial all needed NXXs with the exception of 2 - 540-446-xxxx and 540-658-xxxx. This is really strange! All other NXX numbers can be dialed with no issue. It's just 446 and 658 that are the problem. Calling these exchanges from a cell phone or external analog line works but not via the PABX. The call results in an intercept tone from the carrier after the last digit is entered. The numbers called are verified as good numbers.

Any ideas? I actually opened a ticket with Verizon but of course they think I'm crazy.

 

[bhassell2000]

How are these NXXs built in your dial plan? Something must be different somewhere

 

[GHTROUT]

Do you have to dial NPA 540 first, as you show in your example?

If not, then those NXXs are either not in BARS or your Central Office has a "translations" problem.

To see if it is BARS: Find the Route Access code for the trunk route, dial it from a UNR/TGAR 0 phone, and then dial the NXX+number. If it works, then it's BARS.

If it fails, then it's the CO.

[©] GHTROUT.com [⇔] Resources for Nortel Meridian/CS1000 System Administrators - You Can Hire Me Too

 

[johnpoole]

make sure the nxx is pointed to the same rli.. if so the provider is at fault

john poole
bellsouth business
columbia,sc

 

[old61]

Here is one of the NXX and the route info for it:

REQ PRT
CUST 0
FEAT NET
TRAN AC1
TYPE NXX
NXX 658
RLI 10
SDRR NONE
ITEI NONE
-------------------------------------------
RLI 10
ENTR 0
LTER NO
ROUT 0
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 0
DMI 10
FCI 0
FSNI 0
SBOC NRR
IDBB DBD
IOHQ NO
OHQ NO
CBQ NO
----------------------------------------------------
ROUT 0

TYPE RDB
CUST 00
ROUT 0
DES PUBLICPRI-01
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 12345
NCNA YES
NCRD NO
CHTY BCH
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
MBXR NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR YES
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 1126
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
TTA YES
ABAN YES
CDRB YES
QREC YES
OAL YES
AIA YES
OAN YES
OPD YES
CDRX YES
NATL YES
VRAT NO
MUS YES
MRT 20
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO
---------------------------------------------
DMI 10
DEL 0
ISPN NO
CTYP NCHG

 

[GHTROUT]

What happens if you bypass BARS?

If you bypass BARS, you'll need to account for DMI 10 in your test.

[©] GHTROUT.com [⇔] Resources for Nortel Meridian/CS1000 System Administrators - You Can Hire Me Too

 

[grifc]

Do you have a pri test set? An easy of verifying where the problem is by using a pri test set to make the call. If it works with the test set then the problem lies with the cs1000.

You can also turn on d-channel messages to see why the call is being rejected.

Grifc

Thanks
grifc

 

[old61]

Thanks for all the responses.
Ghtrout I am trying to get a tech in that location to try the call from an UNR/TGAR 0 set. Unfortunately, I do not have a PRI test set so I cannot use that. I will be there tomorrow morning and will pick up with it then. Again, thanks for the suggestions.