Cannot configure Intercom

[nortelopt61]

Hello Everyone,
Running into issue trying to configure (Dig) on a M3904. Here is a copy of the config, any help is greatly appreciated. Trying to add a DIG of 46 # and I cannot get it to go onto this set, yet others that are just like it.

TN 24 0 0 13
DATE
PAGE
DES

DES 3081A
TN 024 0 00 13
TYPE 3904
CDEN 8D
CTYP XDLC
CUST 0
FDN
TGAR 1
LDN NO
NCOS 5
SGRP 0
RNPG 23
SCI 0
SSU
LNRS 16
XLST
CLS CTD FBA WTA LPR PUD MTD FNA HTA TDD HFA GRLD CRPD STSD
MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDA CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDA CFXD ARHD CLTD ASCD
CPFA CPTA ABDA CFHD FICD NAID BUZZ AGRD MOAD AHD
DDGA NAMA
DRDD EXR0
USMD USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN

CPND_LANG ENG
RCO 0
HUNT 6338
LHK 5
PLEV 02
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
MLNG ENG
DNDR 0
KEY 00 SCR 6838 0
CPND
NAME ICU Nurses 1
XPLN 23
DISPLAY_FMT FIRST,LAST
01 SCR 6338 0
CPND
NAME ICU Nurses 1
XPLN 23
DISPLAY_FMT FIRST,LAST
02 SCR 6438 0
CPND
NAME ICU Nurses 1
XPLN 23
DISPLAY_FMT FIRST,LAST
03 SCR 6138 0
CPND
NAME ICU Nurses 1
XPLN 23
DISPLAY_FMT FIRST,LAST
04 SCR 6839 0
CPND
NAME MONITOR TECH
XPLN 23
DISPLAY_FMT FIRST,LAST
05 SCR 7518 0
CPND
NAME ICCU NEW WING NURSE STN
XPLN 23
DISPLAY_FMT FIRST,LAST
06
07
08
09
10
11
12
13
14
15
16
17 TRN
18 AO6
19 CFW 4 7740
20 RGA
21 PRK
22 RNP
23
24 PRS
25 CHG
26 CPN
27 CLT
28 RLT
29
30
31
DATE 27 MAY 2010


NACT

 

[nhphoneguy]

The syntax should be similar to Key 04 DIG 10 2 V.
Make sure the group isn't full.
Not sure if you can only put it on keys 0-5 without an add on module?

 

[GHTROUT]

It can be on any key up to 11.

Key 06 DIG ?? 46 V (but the V might need to be "R".

The entry must end in V or R - whatever the group currently is set as. Ring or Voice



--
GHTROUT.com - Help for Nortel Meridian/CS1000 System Administrators
--

 

[grumpyone60]

Not sure what command you are trying to do,

key 6 dig 46 y r

'46' would be the intercom group you want them in
'y' or 'yy' would be the intercom number for that phone
('y' if group is using single digits 0 thru 9)
('yy' if group is using 2 digits 00 thru 99)
(need to make sure it is a unused number in the group)
'r' would designate it as a ring first
'v' would designate it as a tone then voice
group must be all 'r' or all 'v'

 

[grumpyone60]

do not need add on module, 3904's use shift key to access keys 6 thru 11

 

[nortelopt61]

Hello Everyone,
Thanks I don't know what I was doing wrong, it worked fine this time around. LOL

Thanks,
Jim