Cannot access MC32S card

[antech]

I cannot access MC32S card in both way,either tty 0 on faceplate and tty1 on L adapter.Its new card with out any configuration.Nothing is printing on my serial data interface.Card is booting up and showing UNREG status on faceplate.

 

[Firebird Scrambler]

Does the card have a compact flash on it near to the bottom?. Have you checked that the card has the correct software?

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[KCFLHRC]

First of all I can tell you that if you use the connector on the L connector you have to have a special Nortel cable, I think it's a null cable. If you use the cable off the front I have found that the cable doesn't plug in all the way to the connector. You have to trim some of the rubber off to get it to plug in all the way. The card should have come with the Gold Image on it already from the factory.

 

[antech]

I have 3 mc32s card and 2 of them working perfectly and i could access the card same way and same cable.But third card was not responding.

 

[KCFLHRC]

Sounds like you have a bad card

 

[Reusser]

This bulletin replaces bulletin 2007008546.1. This update has
been issued to communicate some new information regarding
the issue.
BULLETIN ID: 2007008546, Rev 2
PUBLISHED: 2007-12-22
STATUS: Retired
REGION: APAC
CALA
EMEA
GC
NA
PRIORITY: Major
TYPE: Alert
Reissue Reason:
ADDED CONTROLLED SHIP TO TITLE
Background:
NORTEL is investigating reports from the field on the NTDW65/MC32S card that fails to boot into service when first
installed into the system. The output from the face plate LED Display of the NTDW65/MC32S Card reports:
> Self Test
> Load
> UNREG (LED display would stay at UNREG)
The Output from the Face plate connector will show
> Self test Passed
> Auto Booting
At this point the card would no progress through the remainder of the boot cycle and appears to froze
Additionally the output from the Media Card L-adapter from the NTDW65/MC32S reports:
This is the MC32S Gold Image. The vxWorks Image on /p/mainos.sys failed to load
The system has not been installed or there is a problem with the compact flash
Please use setLeader command to enter networking parameters.
Then Install system software using Element Manager or TM
IPL-5.00.31 Wednesday May 23 2007 21:38:13 EDT
Analysis:
During a new installation of this card it has been found that a number of the cards were incorrectly set to be a leader in
the factory. This causes the card to not issue a boot P sequence command.
Recommendations:
.
>TECHNICAL SUPPORT
. TECHNICAL BULLETIN
.
.If a site experiences a failure oif the NTDW65/MC32S as described they should reset the card to follower by using the
mc32ssetup command
Required Actions:
This must be done using the Media Card L-adapter.
This is the MC32S Gold Image. The vxWorks Image on /p/mainos.sys failed to load
The system has not been installed or there is a problem with the compact flash
Please use setLeader command to enter networking parameters.
Then Install system software using Element Manager or TM
IPL-5.00.31 Wednesday May 23 2007 21:38:13 EDT
-> mc32sinfoshow
MC32S Hostname: JK-MC32S
MC32S ELAN IP Address: 47.11.214.83
MC32S Subnet Mask: 255.255.255.224
MC32S Gateway Address: 47.11.214.1
MC32S TLAN IP Address: 47.11.67.183
MC32S Subnet Mask: 255.255.255.224
MC32S Default GW: 47.11.67.177
MC32S Card Role: LEADER
Primary CS Hostname: host
Primary CS IP Address: 47.11.112.21
Primary CS Link : DOWN
MC32S Uptime: 0 days, 0 hours, 0 mins, 32 secs (32 secs)
TLAN set to auto negotiate.
ELAN set to 10Mbps auto negotiate.
ELAN security Disabled
value = 0 = 0x0
-> mc32ssetup ******* Use mc32ssetup to configure the card as a follower
ELAN IP : 47.11.214.83
ELAN subnet mask : 255.255.255.224
ELAN gateway IP : 47.11.214.1
Do you want to configure this card as a leader? (y/n/[a]bort) : n
....
Bootline stored in NV_RAM
Change MC32S advanced parameters? (y/[n]) : n
You have entered the following parameters for this MC32S:
ELAN IP : 47.11.214.83
ELAN subnet mask : 255.255.255.224
ELAN gateway IP : 47.11.214.1
ROLE : FOLLOWER
TLAN set to auto negotiate.
ELAN set to 10Mbps auto negotiate.
ELAN security Disabled
Is this correct? (y/n/[a]bort) : y
The above changes require reboot to take effect.
Do you want to reboot now? (y/n/[a]bort) : y
Attachments:
There are no attachments for this bulletin
Footer Information: