Can not enable MSDL after upgr to rls 5.0

[runlun]

When I have programmed a PRI using qsig to an Alcatel on slot 8 1 8, I am not able to run the
ENL MSDL 8 1 8 all, nothing happens, tried to swap the PRI's on 8 1 1 and 8 1 8, incl. dch, but the same result
Any known issue on rls 5.0?
The tree other PRI's are ok..
From ld 17:

PRI2 MG_CARD
020 000 0 01
021 000 0 02
024 008 1 01
025 008 1 08

 

[tnphoneman]

Stat the TMDI in ld 96?

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[johnpoole]

enl msdl 8 fdl

john poole
bellsouth business
columbia,sc

 

[runlun]

Her is the responses:
.stat tmdi
.

.enl msdl 8 fdl
MSDL001

This is a media gateway (on rls 5.0), we have another PRI with d-channel i 8 1 1, there is no problem on enabling the msdl with the command enl msdl 8 1 1 all.
Have also swappet the two PRI's in 8 1 1 and 8 1 8, still there is no no response on the enl msdl 8 1 8 command
I find it queer type a command, and nothing happens, I have waited for 10 mins, have to type **** to return to the .

 

[tnphoneman]

doesn't make sense that the stat tmdi command came back blank. Latest deplists applied and still in service? Have you installed the firmware patch for the TMDI?

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[runlun]

Latest deplist in service, do you have the firmware patch reference? I am not sure of this one is implementet. Thanks so far

 

[ph0neman]

Try
LD 48

RST MSDL 8 1 8

should come back with OK
and then enable the MSDL

 

[tnphoneman]

The latest loadware for the TMDI is T1E1AA19.LW

I was getting continuous XMI001 and XMI002 messages until I put this loadware into service, even though the T1 was established and I had active calls. It does require a sysload of the system to make it active.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[runlun]

Ok thanks tnphoneman so far, I will try this :->

 

[Phnman]

Try ENL TMDI 8 1 8 FDL in LD 48.

 

[Eddie79it]

Can U please post the iss from Ld 22.
It seems a problem similar to mine problem.
I fixed by upgrading the loadware of the mgc.

 

[runlun]

VERSION 4021
Fine, here's the iss print

RELEASE 5
ISSUE 00 W +
IDLE_SET_DISPLAY Aalesund kommune

IPMG TYPE CSP/SW MSP APP FPGA BOOT DBL1 DBL2

0 0 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A
0 1 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 DSP2AA07
4 0 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A
4 1 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A
8 0 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A
8 1 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A
12 0 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A
12 1 MGC AD31 AA06 AA04 AA12 AD27 DSP1AA07 N/A

 

[Eddie79it]

AD 31 Is quite older and have a known issue with msdl.
You need to upgrade the loadware of MGC card to 45 in order to fix the problem.
If you don't know how to do that let me know.

 

[runlun]

Thanks Eddie79it
I was on my way to this customer just now.
If you have description of the loadware uppg procedure, it would be nice
rgds runlun