Caller ID from Tie Line

[mpemberton]

We have a tie line going from Meridian to CiscoIP phones.

Meridian to CiscoIP phones - Currently says External call (not so much worried about this right now)
CiscoIP to Meridian phones - gives me the internal DN + channel (8908-2, 8908-3, etc)

The tie line is RCLS=EXT, DGTP=DTI, DSEL=3VCE, TKTP=TIE, and ISDN=NO.

What will happen if I change RCLS to INT? When I change it, do I need to disable/enable the tie lines or anything like that? If I do change it to INT, will that "H" precede the number (as I've seen in other posts)? Any other thoughts, comments, or help on this will be most appreciated.

Opt11c rls 22

 

[johnpoole]

no you don't need to disl the loop.. if you make changes on the dch, you need to dis dch x the d auto(ld 96) then disl x the loop, then disl the msdl, then enl msdl x fdl to write that data.. on that system you may need to dis the tmdi also..

john poole
bellsouth business
columbia,sc

 

[johnpoole]

here's an old post that may help, the switch was an 81c but most of those are usable prompts,, this tie is between a ccm and the 81c.. we have msg lamps, names in both direction etc.. took a day or two but this is the

john poole
bellsouth business
columbia,sc

 

[johnpoole]

guess the tab key was stuck down,,,heres the post

http://www.tek-tips.com/viewthread.cfm?qid=1017219

john poole
bellsouth business
columbia,sc

 

[mpemberton]

Thanks John. I'm reviewing the prompts, and it looks very similar, except we're using a T1 rather than ISDN. Don't think that matters much on this specific issue. I see that you're RCLS is EXT. I thought from previous posts I read that I should change it to INT. But with your example as EXT, I should be looking elsewhere. Here's my rdb:

TYPE RDB
CUST 00
DMOD
ROUT 8
DES  AVVID2WAY
TKTP TIE
ESN  NO
CNVT NO
SAT  NO
RCLS EXT
DTRK YES
DGTP DTI
ISDN NO
DSEL 3VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8908
TARG 01
BILN NO
OABS
INST
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
     OGF 512
     EOD 13952
     DSI 34944
     NRD 10112
     DDL 70
     ODT 4096
     RGV 640
     GRD 896
     SFB 3
     TFD 0
SST  5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR  YES
INC  YES
LAST NO
TTA  NO
QREC YES
OAL  YES
AIA  YES
OAN  YES
OPD  YES
NATL YES
MUS  YES
MRT  15
MANO NO
EQAR NO
AUTH NO
TTBL 0
OHTD NO
PLEV 2
ALRM NO
ART  0
SGRP 0

 

[johnpoole]

the reason i am using isdn is so i could modify rcap, msg lamps did not work without it, neither did names.. you can get both on a t without a d channel according to the book but i didn't want to waste to much time, i only had a few days to get two ccm's up and two different switches

john poole
bellsouth business
columbia,sc