Caller ID from the G3si r11 on pri

[Phoneman2]

I have two new PRIs. I will be using them for our outbound dialer. I would like our 800 number to show up on caller id boxes.
I have tried
1, ch isdn pub I put in the trk number and the 800 number with total digits 11. thinking that anything going out that trk would send the 800 number......it don't

2, anything that says send name or number is marked Y in the trk page.

3, I did get the ch ISDN pub working as long as I put in the extension I was calling from.

4, The number that is showing up on the caller ID is my bosses work number.(it would be fun just to leave that way.....but)I'm thinking that when the Ts were setup they put it in to fill in the blank, yes I do have a call into Cox to change that as well.

Here is the trk page for review


Group Number: 2 Group Type: isdn CDR Reports: y
Group Name: Dialer 2 COR: 10 TN: 1 TAC:
Direction: two-way Outgoing Display? y
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: cbc Auth Code? n TestCall ITC: rest
Usage Alloc? n Far End Test Line No:
TestCall BCC: 4 TestCall Service:
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: ascend
Digital Loss Group: 13
Calling Number - Delete: all Insert: 18003672369 Numbering Format: pub-unk
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0



TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n
Suppress # Outpulsing? n Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider

Replace Restricted Numbers? y
Replace Unavailable Numbers? n
Send Connected Number: y

Send UUI IE? y
Send UCID? y
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? y

Network (Japan) Needs Connect Before Disconnect? n






Wisdom is Knowledge
that is Shared

Thanks All Phoneman2

 

[SF0751]

This is what we do:

We have an entry in the cha isdn pub for each sequence of extensions. There is a line with just the number 2 in the first position for all of the extensions begining with a 2, a line with a 3 for all of the extensions beginning with a 3, etc.

[tt] Total
Ext Ext Trk CPN CPN
Len Code Grp(s) Prefix Len

4 2 8009991234 10
4 3 8009991234 10
4 4 8009991234 10
4 5 8009991234 10
4 6 8009991234 10
[/tt]

If I want any exceptions, then I just plug in the full extension, and have the entry read as follows:

[tt] Total
Ext Ext Trk CPN CPN
Len Code Grp(s) Prefix Len

4 4321 210555 10
[/tt]

This would display 210-555-4321 on the receiving caller ID.



Susan
Under certain circumstances, profanity provides a relief denied even to prayer. - Mark Twain

 

[Phoneman2]

Thanks Susan for the reply. I had to change the bill to number on the Ts to one of the new DIDs givin to me by Cox. Then point that number to the CSR vdn on page 3 of the trk form. Its the long way around but Cox didn't want to send an 800 number from a different provider. Wisdom is Knowledge
that is Shared

Thanks All Phoneman2

 

[wsnell]

It depends on what launches the call. If it is a vdn, put the vdn in your isdn pub table. If its a hunt group probably the hunt group extension. Each of the dialers is a little bit different.