call transfer denied

[genice]

I have a one Route ie.(7) incoming call recieved by extn. 555, NIG=555 DAY=555, How can i denied the extn. 555 in transfer the call from other extention.
thanks

 

[fellicciano]

can u repeat the question please

 

[genice]

Hi fellicciano,

here is my inquiry,

Route 7 is programmed as follows:
RODNP:ROU=7;
ROU TRU DAY NIGHT
7 555 555

END.

Meaning incoming calls (from outside ) on this route goes directly to Extn. 555. The extn. also is the only one can access the said route. Once extn. 555 received the outside call, I want to block him/her from transferring the call to other extn. Or once he/she access the line I dont want to transfer to other extension.

thanks

 

[rfpui]

Hi genice
I think that is possible using Traffic Connection matrix . (Command group TC) and setting (changing) TRAF of the ROUte and Extension.
If you have problem how to set this parameter send printout of command:
TCMAP:CON=ALL,
xxCAPIR=555; where xx is KS or EX. I don’t know type of extension 555
ROCAP:ROU=7;
And EXCCP:CAT=ALL;

rfpui
If You want send printout read thread806-898504 before, please.

 

[fellicciano]

i agree with rfpui.If the extension is an EX,i not sure about it,i think there is a way to block flash command in ICAT parameter, but as i said before i not sure about it..

 

[patcher]

This is a big job. You will set the traffic matrix. Example:
555 will have 10 the rest of extensions will be 11 and route 7 will have 12. TCMAS:CON=ALL,A=12,B=10; 12-12, 10-10, 10-11, 11-10, 11-11.. and so on....

 

[rfpui]

Who said that is easy? Not I.

My solution, described below, is possible only if Traffic Connections matrix is set as 15/15.
15/15 is may term or acronym that options are fully open
It is my proposition of traffic matrix:

[tt]
A\B 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
12 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1
13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
14 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
15 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
[/tt]


TCclass (Traffic Connection class) means last two digit in parameter TRAF. ( for route, all type of extension EX, KS, IT and GE )
All extension must have TCclass 14, except Ext 555.
Extension 555 must have TCclass 13.
Route 7 must have TCclass 12.
All other routes, except ROU=7 can have TCclass 15 or 14

To set traffic matrix as above:
TCMAS : A=14, B=14, CON=T;
TCMAS : A=14, B=13, CON=T;
TCMAS : A=13, B=14, CON=T;
TCMAS : A=12, B=13, CON=T;

After send command above not happens in the system
And now is a problem how ( and when ) to make category changes off extensions.
And in fact it is a hard job.
Or not so hard for Mduser who know MD and MSExcel.