Call Name Display on QSIG trunk

[RahjiSupreme]

Is it possible to pass the caller name on a QSIG trunk? I have a QSIG trunk connecting my 61C to a Cisco 2811 router. The 61C is the net and the Cisco is the usr. The 61C dchannel will not allow me to change the RCAP to ND2. It also will not allow me to change the route NCNA and NCRD to yes. I can make inbound and outbound calls, problem is no name is attached, just the extension. Any ideas?

 

[RahjiSupreme]

Here is my config:
REQ PRT
TYPE ADAN DCH 9
ADAN DCH 9
CTYP MSDL
DNUM 11
PORT 1
DES CISCO2800-HD2
USR PRI
DCHL 15
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP QMWI
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7



REQ: PRT
TYPE: RDB
CUST 0
ROUT 8
TYPE RDB
CUST 00
ROUT 8
DES CISCO2800-HD
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8908
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 3968
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096



PAGE 002

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD YES
CDRX NO
NATL YES
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO




REQ: PRT
TYPE: TNB
TN 15 1
DATE
PAGE
DES
DES CISCO2800-HD
TN 015 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 5
RTMB 8 24
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS CTD DTN WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 20 JUN 2007

 

[RS528]

Try this:

RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI


ADAN DCH 11

CTYP MSDL
CARD 01
PORT 1
DES Cisco
USR PRI
DCHL 1
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
QCHID YES
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS NO
T310 120
INC_T306 6
OUT_T306 6
T200 3
T203 10
N200 3
N201 260
K 7

 

[RahjiSupreme]

Still the same issue. However, I need to be the controlling switch, so my SIDE is set to NET, not USR. Other than that, it is the same. Does anybody know the difference between NDI and ND2? It errors when you try to set RCAP at ND2, but not NDI. Also, is there something special to allow the trunk setting of NCNA or NCRD? This is not even an option when configuring the TIE ISGF trunk.

 

[3tdp33ler]

We use
IFC ESGF
RCAP COLP NDO
It works.

 

[RahjiSupreme]

That didn't seem to make a difference for me. Can you please print your config (route & entire dchannel)?

 

[3tdp33ler]

This is M1 11C Rls.3 adv.networking

TYPE RDB
CUST 00
DMOD
ROUT 67
DES IP_GATEWAY
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ESGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 67
TCPP NO
TARG
BILN NO
OABS
INST
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 480
TIDY 67 67
SGRP 0
ANIE 0
AACR NO

ADAN DCH 7
CTYP MSDL
CARD 03
PORT 1
DES IPgateway
USR PRI
DCHL 3
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ESGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
QCHID YES
RCAP COLP NDO
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

 

[3tdp33ler]

Also check your extentions have NAMA and CNDA in CLS.

 

[RahjiSupreme]

I'm using a CDP DSC. No where to set the CLS. If the name were being passed, wouldn't it show up when I do a MSGO on the dchannel? I'm only seeing the extension. I've tried all the configs I've seen on this forum, and never seen my name passed on the MSGO. I'm almost ready to give up

 

[djwht]

you're not going to see name on the dch trace.

there a patch for name display over qsig...I'll see if i can find the patch number

 

[djwht]

the patch is 19510 and applies to all pbx release 4.0 and lower. patch might help and might not, can't hurt...

QNDS: No QSIG name display on tandem call from MCDN to QSIG if IDC is configured on incoming side.

 

[3tdp33ler]

RahjiSupreme

Try to change a dch monitoring level in LD 96
.set msgo 9 mon 2

Then
.enl msgo 9

Look at GFFAC field for name ASCII codes.

 

[johnpoole]

rcap nd1 or nd0 sends name.,, cls is set on the trunk but names do not need a cls mark.. and msgi will send the name.. one thing i did not read.. after you change a rcap or the d.. you have to dis msdl x all then enl msdl x fdl or that change will not take affect..

the msdl needs the download sdl100.. be carefull on the dis msdl x all.. do a map msdl command prior to downing the card..

john poole
bellsouth business
columbia,sc

 

[RahjiSupreme]

I'm going to try these changes after hours since I need to dis msdl. I'll let you know how it went on Monday. Thanks for your help.

 

[MondoMan3]

Hey RahjiSupreme. Did it work for you? I have a similar problem. Some pbx techs told me that here are 2 types of QSIG packages. one is basic, and the second is more advanced. They told me the advanced QSIG will pass the name through. I'm not to sure about that. does anyone else know??

How do you check what QSIG package you have?

 

[RahjiSupreme]

MondoMan3,
Unfortunately, I did not get a chance to make the changes. It's still on my to-do list. I'm preparing for an upgrade from 3.0 to 4.0. You can print the packages in LD 22, but I'm not sure what the difference is in the basic and advanced QSIG. Anyway, I figured if I can get this to work, I'll turn it on after the upgrade. It'll be a nice perk for those executives that they can "see" after signing that $$$ P.O!