Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

BS332 upgrade firmware failed

Status
Not open for further replies.

michalbar

MIS
Nov 23, 2005
9
PL
Hello,
Symptoms: BS looks ok, no alarm in PABX but signal is poor even if my dect is near BS
....so I have decided to update firmware on BS.

ELU31 card blocked and I enter command like below.

FPI = 3, BPOS = 1A-0-40.
Rpn Operating State Blocking State Information
1 Operable Blocked
2 Operable Blocked

MDSH> board_sw -load -bpos 1A-0-40 -ind 0 -file /tftpboot/firmware_BS/DB1R3F.s2
Are you sure? (Y/N): Y
Starting to load /tftpboot/firmware_BS/DB1R3F.s2
to external device on 1A-0-40 with indmask 0x0001

with text ""
Wait for reset of memory for 15 seconds.
Ready to start file transfer.
Bytes to load 322948

All ready 322948 bytes. Ready
Wait for programming flash for 754 seconds.
Position 1A-0-40 flash transfer error detected on board
programming error.
Data transfer ended.
Board 1A-0-40 loaded with /tftpboot/firmware_BS/DB1R3F.s2


Is that means that BS is broken?

System: MX-One 6.3 SP1

regards
Michal


 
upload your firmware file and i test it for you .

PG4E
 
I UPGRADE my bs 332 with this and no any problem so your file is ok
[sup][/sup]
05 DB1-B4/1A1
DB1 PET R1A 7 EXE
DB1 OPERATIONAL GAP R1B 3/80 EXE

PG4E
 
R u near the BS?
Do you have a full signal?
R u connected to this Bs?
Which commend did you used, maybe i forgot somethig

Regards
 
FYI:
I had he same problem with some BS, I had changed this BS to newer one, then upgrade was OK.

here, from release Notes R3G:
Description of changes relative to version R3F
Bug
Not possible to download SW to DB1 under certain conditions
Components: DB1
JIRA: RFP-115
Background: Under certain conditions it is not possible to download software to DB1 if the DB1 is equipped with Macronix flash memory.
Solution: Corrected issue with failed PBX communication during flash erase.
regards
Norbert
 
Is it possible to reflash (downgrade)my BS? How to do that?
right now fw of BS is like below

0 RFP DB1-B3A/1A
0 RFP ROM DB1 PET R1C 7 exe
0 RFP FLASH DB1 OPERATIONAL GAP R1B 3/80 exe

regards
Michal
 
michalbar
hi
you can open cober of one of working bs332 and copy prom ic and write with program on that faulty one bs prom
this need you have air heater gun for pick up and insert prom ic on the board
too many time ago i had problem with an elu31 board when i try update firmware not succefull and board not answer ... so itry with downgrade and upgarde no answer ... after that i found an ok elu31 and copy prom from baord with programmer ... so you can test downgrade or upgrade but anyway you can use my way dont worry this is firmware(prom) problem no anything else....

PG4E
 
Is it easiest way?
I don’t have such technical skills to do that.
Even I dont have an programmer
 
somebody have tool and can do it not so??? find that person and ask him do it...easy way....

PG4E
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top