Bogen Amp with Zone Paging

[rookie13]

I coudn't get this to work with a co port from the PBX. I had to build a 500 port to make it work. Can anyone please post the rdb and tn port if you have the same setup?

I believe this is a bogen tp250 with zone paging.

 

[GHTROUT]

Are you sure it has Zone Paging? Do you have the TAMB? Do you have the ZPM3?

http://www.bogen.com/products/pdfs/telephonepagepdfs/TPU250m.pdf

http://www.bogen.com/products/pdfs/telephonepagepdfs/TAMBm.pdf

http://www.bogen.com/products/pdfs/telephonepagepdfs/ZPM3m.pdf

When you could not get it to work, I assume the specific symptom was: you were unable to... what. You could dial the trunk route access code, and ...what. You could not select a zone? Toggle the MANO prompt in the RDB

~

http://www.GHTROUT.com/

 

[johnpoole]

here's the trunk

DES  PAGE
TN   040 0 00 02
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK  ANLG
NCOS 7
RTMB 20 1
NITE
SIGL LOP
SUPN NO
AST  NO
IAPG 0
CLS  UNR DTN WTA LPR APN THFD
     P10 NTC
TKID
DATE 27 JUL 2004

and here's the route

ROUT 20


TYPE RDB
CUST 00
ROUT 20
DES  PAGE
TKTP COT
NPID_TBL_NUM   0
PRIV NO
SAT  NO
IDEF NET
RCLS EXT
VTRK NO
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8220
CPP  NO
TARG 06
CLEN 1
BILN NO
OABS
TIMR ICF  512
     OGF  512
     EOD  128
     DSI  34944
     NRD  10112
     DDL  70
     OOD  1
     ODT  4096
     RGV  640
     FLH  510
     GRD  896
     SFB  3
     CRD  512

     IENB  5
     TFD  120
     LEXT  100
     VGD  6
SST  3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR  NO
MUS  NO
MR   NO
RACD NO
MANO NO
EQAR NO
FRL  0 0
FRL  1 0


PAGE 002

FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART  0
SGRP 0
AACR NO

two default types of page adapters, one is station level and the other trunk level access.. if your page adapter requires a ring voltage to key the mike, you can't force it to work via a trunk port.. some units are switch selectable, you need one that is loop start.. valcom has both, and i don't know how they stay in business.. anything you buy from them last for decades... i've seen some of their stuff in the field with an inch of dust on it, 20 years after the install. and it still works.. no maint, no problems.. the stuff just works



john poole
bellsouth business
columbia,sc

 

[rookie13]

Yes, it has zone paging where I need to setup the dip switches to tell the paging system what type of tel interface I have. 3 small modules total. I tried building wats, grd, and lop but when I call the paging system I would hear the beep tone. When I press the 00 for all page I would get a fast busy.

I'll try it John.

Thanks y'all

 

[johnpoole]

here's the cure for that. this portion in the rdb sets all 1st ncos's to nfrl table 0

FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0

goto ld 49 and prt crno 0.. i would bet it's not there.. new fcr crno 0, the alow and return... that turns on digits after acod for you paging zones... very very old way to program when we used 9 and acod for local and 8 as acod for ld.. you could build a table for ncos 1, allow every thing except 0 or 1 and that was now your local ncos..

you will not change anyything else except dial access post acod..

john poole
bellsouth business
columbia,sc

 

[GHTROUT]

MANO man-o-man, man.

Just want to make sure the poster has changed the response to LD16 MANO if there has not yet been success.



~

http://www.GHTROUT.com/

 

[rookie13]

I just programmed FCR from ld 49 and this is printout. Will this enable the digits for zone paging after entering the ACOD?

REQ prt
TYPE fcr
CUST 0
CRNO

CRNO 0
INIT ALOW

CRNO 1

CRNO 2

CRNO 3

CRNO 4

 

[johnpoole]

yes because the default is frl 0 7 are all =to crno 0 and it is now an allow table

john poole
bellsouth business
columbia,sc

 

[GHTROUT]

MANO

Only a matter of time



GHTROUT.com | FAQs | Recent Replies

 

[rookie13]

GHTROUT

Should I set mano to yes?

 

[GHTROUT]

Yes Mano



GHTROUT.com | FAQs | Recent Replies