Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Blinking Keys and Local Diagnostic Mode on M2616

Status
Not open for further replies.

Alan Daniels

Technical User
Feb 15, 2017
16
US
thread798-1222751

I have a M2616 phone set on I am receiving blinking Key display on the phone. I did an IDU and receive a NPR0503 (Response timeout from IDU (2 seconds)).

I have reversed the Tip/Ring and phone is completely dead. I have verified that the TN is a Digital Card and the Config is for a 2616.

Below is the the Config for the TN:

DES 7P0408
TN 116 0 12 06
TYPE 2616
CDEN 8D
CTYP XDLC
CUST 0
AOM 0
ERL 0
FDN
TGAR 3
LDN NO
NCOS 3
SGRP 0
RNPG 0
SCI 0
SSU
XLST
SFLT NO
CAC_MFC 0
CLS CTD FBD WTA LPR MTD FND HTD ADD HFA
MWD LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD SLKD CCSD SWD LND CNDD
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN PRMD PHTD PCWD MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD FITD CLTD ASCD
CPFA CPTA ABDD DELD CFHD FICD NAID BUZZ AGRD MOAD
UDI RCC HBTD AHD IPND DDGA NAMA MIND PRSD NRWD NRCD NROD
DRDD EXR0
USMD USRD ULAD CCBD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
FDSD NOVD CDMR MCDD T87D PKCH
CPND_LANG ENG
HUNT
PLEV 02
DANI NO
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 SCR 6874432 0 MARP
01
02
03
04
05
06
07
08 HOT D 4 3019 3119 MARP 0
09
10
11
12
13
14
15
DATE 26 JUL 2017

I did a trap in LD 80. It shows that Key 0 is Idle with a SCR.

 
1. Did you measure the DC voltages on IDF TN ..? I think voltages should be 28 or plus..
2. Did you tried to move the set to other TN ?
3. Change the fuse / surge protector on the IDF TN.
4. Try another set on the same TN.
 
Local Diagnostics mode is invoked by holding down the RLS key when you plug in the phone.
I'd say you have a stuck RLS key.
 
1. Did you measure the DC voltages on IDF TN ..? I think voltages should be 28 or plus..

28 VDC

2. Did you tried to move the set to other TN ?

Yes

3. Change the fuse / surge protector on the IDF TN.

Yes

4. Try another set on the same TN.

Yes

The RLS key is not stuck.
 
At the IDF is 28 vdc and at the site in 19.2 vdc. I do not believe that is too much of a voltage drop.
 
19.2 are insufficient to run a digital set. The line seems to be noisy..check any set at the IDF ..if your answer is also yes to this option then...we have to think more [hourglass]...[smile]
 
I will go way back here, but are you sure you are on a digital line card? Back when we had digital sets, if you plugged into an analog line card TN, the keys would blink.

Just trying to get a little basic here and not meaning to offend anyone.

Hope this helps.

John

John Anaya
Amdocs Inc.
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top