BCN Info needed

[OmegaVTX]

I have some SHOW commands where I get the error
run: File t1.bat show not found.
run: Error at line 100 in file 1:show.bat

Any ideas on how to fix?

Also, how do I console into a BCN, I see a serial interface the SRML module but that is all??

Thanks!!
J

 

[PederChr]

what sw do you run ?

type: stamp

and what files are on the flash

type: dir 1:

SRML is the consol port, there is a strange cabel.. I don't have the pinout :-(

 

[OmegaVTX]

Stamp results:
Image: rel/14.00/
Created: Tue Dec 7 01:00:37 EST 1999

And we dont have support on this so I cannot upgrade

Files in flash:
File Name Size Date Day Time
--------------------------------------------------------
ti.cfg 132 04/12/2000 Wed. 02:36:28
bn.exe 11306787 04/12/2000 Wed. 02:36:30
debug.al 12470 04/12/2000 Wed. 02:39:02
fre4boot.ppc 304696 04/12/2000 Wed. 02:39:05
fre4diag.ppc 497220 04/12/2000 Wed. 02:39:11
freboot.exe 246392 04/12/2000 Wed. 02:39:19
frediag.exe 244484 04/12/2000 Wed. 02:39:26
install.bat 246150 04/12/2000 Wed. 02:39:31
bcc_bn.hlp 530691 04/12/2000 Wed. 02:39:37
show.bat 15306 04/12/2000 Wed. 02:39:47
ppp.bat 105667 04/12/2000 Wed. 02:39:49
isdn.bat 39452 04/12/2000 Wed. 02:39:53
hardware.bat 45374 04/12/2000 Wed. 02:39:55
system.bat 19789 04/12/2000 Wed. 02:39:58
process.bat 69581 04/12/2000 Wed. 02:40:01
log.txt 268756 06/26/2001 Tues. 15:10:43
bootp.bat 10387 07/13/2001 Fri. 17:55:22
bootp.mnu 745 07/13/2001 Fri. 17:55:24
bcn_031302.cfg 257292 03/13/2002 Wed. 11:16:17
config523 178312 05/21/2002 Tues. 09:36:54
config.2 69148 05/28/2002 Tues. 07:58:41
config.cfg 5140 12/11/2003 Thurs. 16:05:51
config051205 183632 05/12/2005 Thurs. 09:17:53
tftp 15306 04/12/2000 Wed. 02:39:47
config7705 183992 07/07/2005 Thurs. 11:53:13
bncjason 184644 11/15/2005 Tues. 17:49:37
bcn112805 184644 11/28/2005 Mon. 09:39:29
bcn121605 185288 12/16/2005 Fri. 14:51:33
bcn122105 328516 12/21/2005 Wed. 11:06:53
bcnlog012406 328220 01/24/2006 Tues. 09:33:21
config 185916 01/27/2006 Fri. 11:56:16


Thanks for the info... I will try to find the pin out.

 

[dane775]

The "show" commands only provide basic info for certain things like IP circuits. Most "show" commands require the associated .bat files to be present.

You don't have the t1.bat file present on your PCMCIA card, which is why you're getting that error.

 

[dane775]

Here are the things that you get basic info for without any batch files present:

csmacd fr ftp ip snmp
sync tcp telnet tftp

As far as your console cable:

You have to cross the pins to an ASCII terminal. The router interface is a DTE type inteface. Tx Data out on pin 2, Rx Data in on pin 3, etc.

Good luck!!

 

[OmegaVTX]

Thanks for the info!!