AUD/BUG error-Rls 5.5 CPPIV, 81c

[chintoo69]

Hi, i have upgraded a 61c rls 25.40 to CS1000M,MG (81c) release 5.5 CPPIV with old database conversion into rls 5.5 format. Aftter upgrading i am getting following BUG/AUD errors randomly all day, patches are up to date. Any advise?

CAPTURE
--------
AUD029 00F0D3E8 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0
0000000


AUD029 00E58EFC 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0
0000000


AUD029 00E58EFC 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0
0000000


AUD029 00F0D3E8 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0
0000000


AUD029 00E58EFC 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0
0000000


AUD029 00E58EFC 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0
0000000

*************************************************

BUG040
BUG040 : 4 000005BD 0 00000000 00002747 00000000 075F60B0 00000100 00000008 0000
0000 00000000 6 075855E2 00000001 00000000 0 00000000 00000000 00000000 0000000
0 00000000 00000000 00000000
BUG040 + 00B33E62 00AD6AC6 00DA2BC5 00DA103F 00B296B7
BUG40 + 01BC790F 01BC553A 01BC532A 01BC13BA 01BAA03B
BUG040 + 1329DEF9 01B8B53E 01B7F682 01B03387 01B0208B
BUG40 + 01B01AE9 01AFEDFA 01AFB7E3 01B68F62 01B6885D
BUG040 + 01B68503 01B683EC 011107FC

BUG279
BUG279 : 075F60B0 00000100 00000008 00000000 00000000 0 00000000 00000000 000000
00 0 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BUG279 + 00B33E62 00B296C2 01BC790F 01BC553A 01BC532A
BUG279 + 01BC13BA 01BAA03B 1329DEF9 01B8B53E 01B7F682
BUG279 + 01B03387 01B0208B 01B01AE9 01AFEDFA 01AFB7E3
BUG279 + 01B68F62 01B6885D 01B68503 01B683EC 011107FC
****************************************************
BUG4005
BUG4005 : 00000FAC 00000002 075B321E 00000607 00008308 00000000 00000FAC 0 0000
0000 00000000 00000000 0 0000A18C 000033A9 00001633 00006367 00000000 00000000
00000000
BUG4005 + 00B33E62 00B2AB81 00B29D12 01BC790F 01BC553A
BUG4005 + 01BC532A 01BC13BA 01BAA03B 13239470 01B8B589
BUG4005 + 01B7F682 01B03387 01B0208B 01B01AE9 01AFEDFA
BUG4005 + 01AFB7E3 01B69442 01B687AD 01B68503 01B683EC
BUG4005 + 011107FC


I am getting these type of errors after every 5 or 10 minutes.

 

[bigindian65]

you checked the DEP list against Nortel site? Patched up to date?


Mato' Was'aka

 

[9201]

For AUD029 check TN 12-0-1-9 either out and rebuild on another card. BUG279, check your DTR the other are minor happen are the times.

 

[chintoo69]

Updated patches are loaded 8 hours ago, so may be it isnt patch issue. What shud i check for DTR, they seems to OK, tested these and found nothing.
Any other advice?

 

[chintoo69]

Any more help in this?? from others too??

 

[GHTROUT]

In LD 32, I'd do the .CONV on each of these (taken from the AUD message) , then disable and re-enable them if they are valid TNs

LD 32

.conv D3E8

.conv 0C04

.conv 0C85

.conv 8EFC

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[chintoo69]

Hi GH, some of these CONV XXXX command wont show any TN.i just get dot (.) after executing commands with some hex code, what should i do for these.
Another thing is that i also get an error whih says "A non IDLE DTR found, Contact technical support" with sevrity MAJOR. I checked all my DTR they r OK and also tested these through commands but still shows these DTR OK.
Regards

 

[GHTROUT]

The .CONV that do not show a TN, just ignore. Disable/Re-enable the ones that are TNs.

As for the DTR, Do a LD34 .DISR and .ENLR that DTR Card.

There is no valid DTR "Test" you can do from command line, even though the books tell you there is. The only valid test is to remove all of them and put them in one at a time and make calls from an analog TN. This is the only way to be certain a DTR works.

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]