Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Aruba AP on Avaya Switch

Status
Not open for further replies.

LMQ1128

IS-IT--Management
Nov 19, 2019
2
PH
Hi Guys,

Just a newbie in handling Avaya Switch and have some difficulties in terms of tag and untag for Aruba AP. We have a new Aruba access point that needs to be configured via Radius server, my problem is I cannot get any IP from the Radius server even though I already untagged with pvid X. please see details below

BEB-23#
BEB-23#
BEB-23#sh int 6

BEB-23#
BEB-23#
BEB-23#
BEB-23#
BEB-23#sh int 6/31 con
Unit/Port: 6/31
Trunk:
Admin Status: Enable
Oper Status: Up
EAP Oper Status: Up
VLACP Oper Status: Down
STP Oper Status: Forwarding
Link: Up
Last Change: 0 day(s), 00h:20m:00s ago
LinkTrap: Enabled
Link Autonegotiation: Enabled
Link Speed: 1000Mbps
Link Duplex: Full-Duplex
Flow Control: Disable
Energy Saver: Disabled
Energy Saver Oper Status: No Power Saving
BPDU-guard (BPDU Filtering): Disabled
BPDU-guard (BPDU Filtering) Oper Status: N/A
SLPP-guard: Disabled
SLPP-guard Oper Status: N/A

*****VLAN interfaces configuration*****
Filter Filter
Untagged Unregistered
Unit/Port Frames Frames PVID PRI Tagging Name
--------- -------- ------------ ---- --- ------------- ----------------
6/31 No Yes 85 0 UntagAll Unit 6,Port 31

*****VLAN ID port member configuration*****
Unit/Port VLAN VLAN Name VLAN VLAN Name VLAN VLAN Name
--------- ---- ---------------- ---- ---------------- ---- ----------------
6/31 11 Support 85 VSTECS_Wifi 88 MISTECH
--------- ---- ---------------- ---- ---------------- ---- ----------------

*****Spanning-tree port configurations*****
Unit Port Trunk Participation Priority Path Cost State
---- ---- ----- --------------- -------- --------- ----------
6 31 Normal Learning 128 1 Forwarding
BEB-23#


I hope you can help me with this.

Thanks,
Garry


































 
It looks like the port is set to untagall, so the only VLAN available on that port would be the native VLAN (whatever is set as the PVID). Without seeing the whole config, its hard to say. It may be as simple as using 'vlan port 6/31 tagging untagpvid' if you need two VLANs on that port.

If you need an untagged and tagged VLAN to that AP, you can do something like the below, assuming both VLANs are already configured on the switch:

vlan member add 6/31 85 (adds VLAN 85 to port 6/31)
vlan member add 6/31 88 (adds VLAN 88 to port 6/31)

vlan port 6/31 tagging untagpvid (tells the switch to untag traffic to the native VLAN/PVID)
vlan port 6/31 pvid 85 (if you want VLAN 85 untagged and 88 tagged - put the native VLAN you want on that port after the word PVID)










 
Hi biv343,

Thank you for the response, appreciate it much. So for me to untag and tag each VLAN, I need to do Vlan member add 6/31 85 before I tag and untag the vlan ports? or it doesn't matter if I do first the tagging?

Thank you,
Garry
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top