Analog DID trunks

[1Gordo]

Need some help with new Analog DID trunks, when the call is received from the PSTN, I am only receiving the first digit then the switch is sending reorder, like it is not waiting long enough for all digits. I can see that during an enhanced trace. Here are my trunk and route blocks.


REQ: prt
TYPE: tnb
TN 0 0 3 0
DATE
PAGE
DES

DES DID
TN 000 0 03 00 VIRTUAL
TYPE DID
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 7
RTMB 1 1
NITE
SIGL LDR
STRI WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD SPCD
P10 NTC
TKID
AACR NO
DATE 27 JAN 2016


NACT
REQ: ****
OVL000
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 1

TYPE RDB
CUST 00
ROUT 1
DES DID
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK NO
ISDN NO
PTYP ACO
CNDP UKWN
AUTO NO
DNIS NO
ICOG ICT
STEP
ACOD 25001
TARG
CLEN 1
BILN NO
OABS
INST
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3

IENB 5
VSS 0
VGD 6
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 20
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO


PAGE 002

OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

REQ:

 

[PERRYPJ]

Can you get on the TIP and RING of the trunk at the Demark and make a call in

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[1Gordo]

I did put my butt set on it and called a DID with another set, the trunk goes active, I can hear all DTMF tones, however after the first digit I can also hear the PBX sending out the reorder.

 

[KCFLHRC]

Do you have something set in the LDN_DATA? You have to have a 4 digit # set there otherwise it will reject the call

 

[KCFLHRC]

It would need to look something like this. Notice the 6000 under LDN0?

ld 21
PT1000

REQ: prt
TYPE: ldn
TYPE LDN_DATA
CUST 0

TYPE LDN_DATA
CUST 00
OPT XLDN
DLDN NO
LDN0 6000
LDN1
LDN2
LDN3
LDN4
LDN5
ICI 00 LD0
ICI 01 DL0
ICI 02 RLL
ICI 03 INT
ICI 04
ICI 05 CFB
ICI 06 CFN
ICI 07
ICI 08
ICI 09

 

[1Gordo]

Yes, we actually have 5 digit extensions and my LDN is 5 digits long. I have not used analog DID trunks in about 10 years, who uses those anymore!!

 

[KCFLHRC]

So the 5 digits you are trying to pulse in are the same as your 5 digit Ext #'s?

 

[KCFLHRC]

Also make the NCOS 0 on the trunk, why is it 7?

 

[1Gordo]

yes example is 715-561-3215 is extension 13215, the NCOS is set to 7 for trunk to trunk connections and LD service

 

[KCFLHRC]

So you can call 13215 internally, right?

 

[1Gordo]

yes no problem with internal, on network, or outgoing calling, just these analog DIDs, is there a timer someplace that I am missing that would listen longer to the incoming DTMF tones? When I do an enhanced trace on the trunk I can see the dialed digits only contains the 7, I was going to put just a 7 as a DN on a phone but there are over 200 CDP entries that start with 7.

 

[KCFLHRC]

Just to appease me make that NCOS 0 and try it. Because it looks like everything else is right. Also pull off the jumper connecting the CO and just put your butt set on the TN, come off hook, an put in the digits. Keep in mind copper DID trunks are polarity sensitive also.

 

[KCFLHRC]

You should hear the battery reversal on the TN on your butt set for the wink start. Should go click then click

 

[1Gordo]

I changed the NCOS to 0, did not help. I also did a trace to show you I am just receiving the 7. I am not at site but will stop there on my way in and give the butt set a try


MEM AVAIL: (U/P): 39897168 USED U P: 4804978 177723 TOT: 44879869
DISK SPACE NEEDED: 201 KBYTES
AST AVAIL: 400 USED: 0 TOT: 400
ITG ISDN TRUNKS AVAIL: 0 USED: 0 TOT: 0
IP PEER H.323 TRUNKS AVAIL: 30 USED: 0 TOT: 30
RAN CON AVAIL: 120 USED: 0 TOT: 120
MUS CON AVAIL: 119 USED: 1 TOT: 120
IP RAN CON AVAIL: 120 USED: 0 TOT: 120
IP MUS CON AVAIL: 120 USED: 0 TOT: 120
IP MEDIA SESSIONS AVAIL: 350 USED: 0 TOT: 350
TNS AVAIL: 4914 USED: 86 TOT: 5000
DATA PORTS AVAIL: 2500 USED: 0 TOT: 2500
SIP ACCESS PORTS AVAIL: 0 USED: 30 TOT: 30
TRADITIONAL TRUNKS AVAIL: 118 USED: 2 TOT: 120
ELC ACCESS PORTS AVAIL: 30 USED: 0 TOT: 30
REQ new 3
TYPE did
TN 0 0 3 0
DES DID
XTRK XUT
CUST 0
NCOS 0
RTMB 1 1
INC
NITE
SIGL ldr
TIMP
BIMP
STRI wnk
AST
CLS unr dtn wta
TKID

NEW TRK TN 000 0 03 00 RT 1 MB 1

MEM AVAIL: (U/P): 39896916 USED U P: 4805149 177804 TOT: 44879869
DISK SPACE NEEDED: 201 KBYTES
AST AVAIL: 400 USED: 0 TOT: 400
ITG ISDN TRUNKS AVAIL: 0 USED: 0 TOT: 0
IP PEER H.323 TRUNKS AVAIL: 30 USED: 0 TOT: 30
RAN CON AVAIL: 120 USED: 0 TOT: 120
MUS CON AVAIL: 119 USED: 1 TOT: 120
IP RAN CON AVAIL: 120 USED: 0 TOT: 120
IP MUS CON AVAIL: 120 USED: 0 TOT: 120
IP MEDIA SESSIONS AVAIL: 350 USED: 0 TOT: 350
TNS AVAIL: 4913 USED: 87 TOT: 5000
DATA PORTS AVAIL: 2500 USED: 0 TOT: 2500
SIP ACCESS PORTS AVAIL: 0 USED: 30 TOT: 30
TRADITIONAL TRUNKS AVAIL: 117 USED: 3 TOT: 120
ELC ACCESS PORTS AVAIL: 30 USED: 0 TOT: 30
NEW TRK TN 000 0 03 01 RT 1 MB 2

MEM AVAIL: (U/P): 39896676 USED U P: 4805320 177873 TOT: 44879869
DISK SPACE NEEDED: 201 KBYTES
AST AVAIL: 400 USED: 0 TOT: 400
ITG ISDN TRUNKS AVAIL: 0 USED: 0 TOT: 0
IP PEER H.323 TRUNKS AVAIL: 30 USED: 0 TOT: 30
RAN CON AVAIL: 120 USED: 0 TOT: 120
MUS CON AVAIL: 119 USED: 1 TOT: 120
IP RAN CON AVAIL: 120 USED: 0 TOT: 120
IP MUS CON AVAIL: 120 USED: 0 TOT: 120
IP MEDIA SESSIONS AVAIL: 350 USED: 0 TOT: 350
TNS AVAIL: 4912 USED: 88 TOT: 5000
DATA PORTS AVAIL: 2500 USED: 0 TOT: 2500
SIP ACCESS PORTS AVAIL: 0 USED: 30 TOT: 30
TRADITIONAL TRUNKS AVAIL: 116 USED: 4 TOT: 120
ELC ACCESS PORTS AVAIL: 30 USED: 0 TOT: 30
NEW TRK TN 000 0 03 02 RT 1 MB 3

MEM AVAIL: (U/P): 39896436 USED U P: 4805491 177942 TOT: 44879869
DISK SPACE NEEDED: 201 KBYTES
AST AVAIL: 400 USED: 0 TOT: 400
ITG ISDN TRUNKS AVAIL: 0 USED: 0 TOT: 0
IP PEER H.323 TRUNKS AVAIL: 30 USED: 0 TOT: 30
RAN CON AVAIL: 120 USED: 0 TOT: 120
MUS CON AVAIL: 119 USED: 1 TOT: 120
IP RAN CON AVAIL: 120 USED: 0 TOT: 120
IP MUS CON AVAIL: 120 USED: 0 TOT: 120
IP MEDIA SESSIONS AVAIL: 350 USED: 0 TOT: 350
TNS AVAIL: 4911 USED: 89 TOT: 5000
DATA PORTS AVAIL: 2500 USED: 0 TOT: 2500
SIP ACCESS PORTS AVAIL: 0 USED: 30 TOT: 30
TRADITIONAL TRUNKS AVAIL: 115 USED: 5 TOT: 120
ELC ACCESS PORTS AVAIL: 30 USED: 0 TOT: 30
REQ ****
OVL000
>

OVL000
>ld 20

PT0000
REQ: prt
TYPE: tnb
TN 0 0 3 0
DATE
PAGE
DES

DES DID
TN 000 0 03 00 VIRTUAL
TYPE DID
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 0
RTMB 1 1
NITE
SIGL LDR
STRI WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD SPCD
P10 NTC
TKID
AACR NO
DATE 27 JAN 2016


NACT ****
OVL000
>ld 80
TRA000
.entc 0 0 3 0 0100


gotr


.14:43:44 27/01/2016
IDLE TN 000 0 03 00


.14:44:04 27/01/2016
ACTIVE TN 000 0 03 00 IPMG 000 0

ORIG TN 000 0 03 00 IPMG 000 0 V PHYSICAL TN 000 0 00 00 DID RMBR 1 1 INCOMING TRUNK CALL
TERM NONE
TTR 000 0 14 06
DIAL 128 0 0 TTR 0 0
RCVR 57 SET 20

DIAL DN NONE
MAIN_PM READY
TALKSLOT NONE
EES_DATA:
NONE
QUEU DIAL
CALL ID 715 19676





.14:44:04 27/01/2016
ACTIVE TN 000 0 03 00 IPMG 000 0

ORIG TN 000 0 03 00 IPMG 000 0 V PHYSICAL TN 000 0 00 00 DID RMBR 1 1 INCOMING TRUNK CALL
TERM NONE
TTR 000 0 14 06
DIAL 128 0 0 TTR 0 0
RCVR 57 SET 20

DIAL DN 7
MAIN_PM DIAL AUX_PM DNTRAN
TALKSLOT NONE
EES_DATA:
NONE
QUEU NONE
CALL ID 715 19676





.14:44:06 27/01/2016
ACTIVE TN 000 0 03 00 IPMG 000 0

ORIG TN 000 0 03 00 IPMG 000 0 V PHYSICAL TN 000 0 00 00 DID RMBR 1 1 INCOMING TRUNK CALL
TERM NONE
TDTN 128 SLOT 0 10 PTY SLOT 0 15
DIAL DN NONE
MAIN_PM REOR
TALKSLOT NONE
EES_DATA:
NONE
QUEU DIAL
CALL ID 715 19676





.14:44:10 27/01/2016
ACTIVE TN 000 0 03 00 IPMG 000 0

ORIG TN 000 0 03 00 IPMG 000 0 V PHYSICAL TN 000 0 00 00 DID RMBR 1 1 INCOMING TRUNK CALL
TERM NONE
DIAL DN NONE
MAIN_PM HALFDISC
TALKSLOT NONE
EES_DATA:
NONE
QUEU DIAL
CALL ID 715 19676





.14:44:12 27/01/2016
IDLE TN 000 0 03 00


.

 

[KCFLHRC]

My guess is then the CO is not sending you the last 5 digits, it looks like they are sending you all 10 hence the 7

 

[1Gordo]

Yes that is correct, they send all 10, and with the LDN set to 5 digits the PBX only looks at the last 5

 

[KCFLHRC]

I think you are wrong about that. But do the butt set test and only pulse in the last 5 digits, I bet it works then. I think what you are referring to is only applicable to T-1 or PRI.

 

[StanleySteamer]

I agree with KCFLHRC. With analog DIDs the CO is sending digits individually in order. So your switch is translating them in the order they arrive. It's different with a PRI.
You will have to put in an IDC table and associate with the DID route so that it converts 715561 to 1. Then the remaining digits would be translated to complete the DN.

 

[1Gordo]

Wow, been working on Nortel for 20 years and never seen this before, like I said who uses analog DIDs anymore right. Big gold star to KCFLHRD and StanleySteamer!! You guys rock, tested with the butt set and the call went through, built the IDC tables and boom, all is well. Thanks again.