Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

AMO SIPCO Error 3

Status
Not open for further replies.

Hamid2018

Technical User
Aug 26, 2018
63
IR
thread965-1716275

Dears
Hello
I have an Openscape 4000 with no AP shelf, and visibly no APE unit.
but every some times on the System following error acours in the Dis-LOGBK.

P10151 DEV:USER TSN:3120 UID:2 NOUN:SIPCO TYPE:START TIME:21-09-06 11:47:12
CHANGE-SIPCO:LSNET,,,,,,,,,,0.0.0.0;

P10152 DEV:USER TSN:3120 UID:2 NOUN:SIPCO TYPE:OUTPUT TIME:21-09-06 11:47:12
H20: THE IP ADDRESSES OF LSNET ARE NOT CONFIGURED. THE CURRENTLY
CHANGED SYSTEM PARAMETERS WILL HAVE NO EFFECT AT THE MOMENT


P10153 DEV:USER TSN:3120 UID:2 NOUN:SIPCO TYPE:OUTPUT TIME:21-09-06 11:47:12
F05: SOME PARAMETERS ARE NOT PLAUSIBLE CONCERNING THE COMBINATION OF
NET ADDRESS 0.0.0.0 AND NET MASK 0.0.0.0.
FOLLOWING REASONS CAN CAUSE THIS ERROR :
- COMBINATION OF NET ADDRESS AND NET MASK IS INPLAUSIBLE
- THE GIVEN PARAMETER IS NOT AN ADDRESS WITHIN THE ACTUAL NET SEGMENT
- THE GIVEN PARAMETER DOES NOT FIT INTO THE ACTUAL NET ANYMORE BECAUSE OF
CHANGED NET ADDRESS AND/OR NET MASK. THEREFORE IT HAS TO BE RE-PROMPTED.


P10154 DEV:USER TSN:3120 UID:2 NOUN:SIPCO TYPE:END TIME:21-09-06 11:47:12
CHANGE PARTIALLY COMPLETED;

P10155 DEV:FAS TSN:0205 UID:3 NOUN:SIPCO TYPE:START TIME:21-09-06 11:47:13
REGENERATE-SIPCO:Y;

P10156 DEV:FAS TSN:0205 UID:3 NOUN:SIPCO TYPE:END TIME:21-09-06 11:47:14
REGENERATE COMPLETED;

P10157 DEV:USER TSN:3117 UID:2 NOUN:UCSU TYPE:START TIME:21-09-06 11:47:17
REG-UCSU;

P10158 DEV:USER TSN:3117 UID:2 NOUN:UCSU TYPE:END TIME:21-09-06 11:47:17
REGENERATE COMPLETED;

P10159 DEV:USER TSN:3117 UID:2 NOUN:APRT TYPE:START TIME:21-09-06 11:47:27
REG-APRT;

P10160 DEV:USER TSN:3117 UID:2 NOUN:APRT TYPE:END TIME:21-09-06 11:47:27
REGENERATE COMPLETED;

P10161 DEV:USER TSN:3117 UID:2 NOUN:SIGNL TYPE:START TIME:21-09-06 11:47:37
DIS-SIGNL:SYSTEM;

The IP addresses of system are as following:

<common>
system-deployment=simplex
customer-portal.ip=192.168.10.4/24
customer-lan.assistant-ip-address=192.168.10.5/24
customer-lan.csta-ip-address=192.168.10.6/24
atlantic-interface.0=bond4
ipda-interface=bond1
ipda-lan.cca-ip-address=192.168.10.11/24
ipda-lan.default-router-ipda=192.168.10.1
internal-lan.network=192.168.187.0
customer-def.gw=192.168.10.1
system.rtm-configured=1

<node1>
customer-interface=bond1
bond1.dev.0=eth0
bond1.dev.1=eth1
bond1.ip.0=192.168.10.2/24
bond1.hostname.0=office
bond2.dev.0=eth2
bond2.dev.1=eth3
bond2.ip.0=0.0.0.0/0
bond3.dev.0=eth4
bond3.dev.1=eth5
bond3.ip.0=0.0.0.0/0
bond4.dev.0=eth6
bond4.dev.1=eth7
bond4.ip.0=0.0.0.0/0
customer-dns.server.0=192.168.10.1
customer-ntp.server.0=192.168.10.1
customer-keyboard-layout=english-us
customer-def.gw.dev=bond1


Current SIPCO is default:

CHA-SIPCO:DIFFSERV,184,104,N,0,16384;
CHA-SIPCO:TIMING,60,300,4,5,60;
CHA-SIPCO:pLQUAL,200,120,10,4;
CHA-SIPCO:BANDW,15,36,;
CHA-SIPCO:DMCDATA,N,G711;
CHA-SIPCO:SECURITY,N,24,128CBC;

1- Why does this error raises?

2- Is this SIPCO command correct to insert?
ADD-SIPCO:NETADDR=192.168.10.0,NETMASK=255.255.255.0,IPMODE=IPV4,DEFRT=192.168.10.1,CCAADDR=192.168.10.11,CCBADDR=192.168.10.12,SURVNET=0.0.0.0,DHCPV4=N,DHCPV6=N;
 
SIP settings are configured via the web interface of the HG card, not AMO
 
Dear thepfy

Thank you for tour replay.
so there is no need to add sipco net address like the command mentioned before?
 
No, our 4K's don't have the IP set in SIPCO.
 
SIPCO is added in the XML file used to setup the OS4K initially.
 
Dears
Thank you I found the systems XML file in the SUSE and add the SIPCO comand as required.

Best Regards
Hamid
 
You've done what? ADD-SIPCO is an RMX command, added on the 4K using Comwin. You don't put it in your XML file. If you've put that ADD-SIPCO line in your firstinst XML, you have corrupted your XML file. Which isn't a problem, just take the line out.

Your post title is misleading "IPDA goes down everyday". You don't have any IPDA. You don't have SIPCO IP addresses added. If you have no SIPCO IPs you have no IPDA. So it can't go down.

Your XML file shows you have a simplex system with IPDA sharing the customer LAN interface (instead of bond0 for customer LAN and bond1 for IPDA). You have both interface types on the same bond (bond1). So you have a physical NIC IP of 192.168.10.2, for both customer and IPDA. Your ipda-lan.cca-ip-address is 192.168.10.11. That is the IP to use in your ADD-SIPCO line (for CCA), which is almost correct, but you specified CCB also, 192.168.10.12, and your system is simplex, you have no CCB, you leave that parameter blank in ADD-SIPCO.

So you can add that line in your RMX if you wish, if you have no IPDA it doesn't matter if it's there or not. The warnings from dis-logbk would disappear, but they don't matter anyway. BP processor needs a soft restart after SIPCO changes.

You should correct your XML though because if you've put that ADD-SIPCO line in it, you've broken it.

"SIP settings are configured via the web interface of the HG card, not AMO" is relevant for native SIP trunk configurations, and even in that case, AMO (CGWB) is still required for config. However, SIPCO is used for IPDA shelves and configures the central signaling IP configuration of the host 4K, it's nothing to do with trunks.
 
Dear Moriendi
thank you for your kind help, yes the CCB should be clear but I found the SIPCO parameter in XML file and added the AMO SIPCO in comwin.
I found what I needed.

Best Regards
Hamid
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top