Adding a second TMDI card to an existing TIE trunk group 1

[TelecomTony]

Hello,

I setup a TIE line between my Nortel and Avaya system. Everything is working great!

I am trying to add a second TMDI card to this existing trunk group to expand it from 23 channels to 47 and I am getting the following error message when I add the RTMB as 70 24.

SCH4788
PRI loop is not configured with D-channel (DCHI) to provide
B-channels.

Severity: Info

Loop 65 is the original TIE. I added loop 66 as the second loop. I am only using 1 D channel


Here is my CEQU data for the new card and loop.

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 020 24 ESF NO B8S FDL - 00 000 0 01
021 24 ESF NO B8S FDL - 00 000 0 02
026 24 ESF NO B8S FDL - 00 000 0 07
065 23 ESF YES B8S FDL 0 00 004 1 06
066 24 ESF YES B8S FDL 0 00 004 1 07

Here is my RDB for the TIE line.

TYPE RDB
CUST 00
ROUT 70
DES AVAYATIES
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 80
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN YES
AACR NO

Here is the trunk programming.

DES AVAYATIE
TN 065 01 VIRTUAL
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 70 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS CTD DIP CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 7 MAR 2016

Regards

 

[bhassell2000]

So you are adding it to the original DCH? Did you change ADAN programming to add the loop to the DCH?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[Trason806]

I always use a separate dch for each t1. you only lose one channel, and if you need to do any kind of maint on it you can still run each t1 individually.

 

[KCFLHRC]

It's telling you exactly what is wrong. You never configured a D-channel for that loop

 

[TelecomTony]

Here is the current DCH that I am using for TIE.

ADAN DCH 10
CTYP TMDI
MG_CARD 004 1 06
PORT 1
DES avayatie
USR PRI
DCHL 65
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 3 1
CNG 3 1
CON 3 1
CTR2 3 1
PR_RTN NO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

Do I need to add another for the additional loop if I am just expanding the original one?

 

[KCFLHRC]

Yes you do. Or you can share the D-channel if configured on the other end the same way

 

[bhassell2000]

it needs a DCH, either use the existing one and add it in the adan programming or build a new DCH for the new loop, has to match how you are planning to build it on the other end

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[TelecomTony]

I just want to share the same D channel as that is what I am doing. As well the TMDI card I am using does not have the additional d channel board to support it.

 

[bhassell2000]

so change the programming in ld 17 at the PRI prompt add the new loop number

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[KCFLHRC]

TMDI does not require a D-channel board

 

[KCFLHRC]

Do a change on the d-channel and at the PRI prompt enter 66. You will more than likely have to disable the D-channel to do this

 

[bhassell2000]

the only daughter board I remember on a TMDI was a clock controller card

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[TelecomTony]

thank you I will give this a try after hours as I have to take down my d channel!

 

[Trason806]

I use MSDL for DCH. 4 per card. What else are those things good for?

 

[KCFLHRC]

You cant use an MSDL Card with a TMDI. You can use Port 0 for a TTY port if needed. Other than that D-channels.

 

[Trason806]

you can disable the DCH and not drop the T1. You just cant establish new calls while it is disabled. Calls already established will remain connected.