An A5000 that was recently attached to a Sun 450 (running Solaris 7) appears to have a few disks in the enclosure that have problems. This is a new array, so before I blindly assume they are simply bad disks, I was wondering if someone could help me interpret the following message:
# luxadm display ORLANDO
SENA
DISK STATUS
SLOT FRONT DISKS (Node WWN) REAR DISKS (Node WWN)
0 On (Not Ready) 2000002037337221 On (O.K.) 20000020372b5a14
1 On (O.K.) 20000020372b5594 On (O.K.) 20000020372b4e58
2 On (Not Ready) 200000203726fe15 On (O.K.) 20000020374fa786
3 On (O.K.) 20000020372b5079 On (Not Ready) 200000203733d4cf
4 On (O.K.) 20000020372b4d63 On (O.K.) 20000020372b4991
5 On (O.K.) 20000020372b4fa4 On (O.K.) 2000002037457705
6 On (Open Failed) 200000203722d50e On (O.K.) 200000203726ea2a
SUBSYSTEM STATUS
FW Revision:1.09 Box ID:0 Node WWN:5080020000049358 Enclosure Name:ORLAND
Power Supplies (0,2 in front, 1 in rear)
0 O.K.(rev.-02) 1 O.K.(rev.-02) 2 O.K.(rev.-02)
Fans (0 in front, 1 in rear)
0 O.K.(rev.-04) 1 O.K.(rev.-00)
ESI Interface board(IB) (A top, B bottom)
A: O.K.(rev.-04)
GBIC module (1 on left, 0 on right in IB)
0 O.K.(mod.-01)
1 Not Installed
B: O.K.(rev.-04)
GBIC module (1 on left, 0 on right in IB)
0 O.K.(mod.-01)
1 Not Installed
Disk backplane (0 in front, 1 in rear)
Front Backplane: O.K.(rev.-04)
Temperature sensors (on front backplane)
0:37ºC 1:37ºC 2:37ºC 3:37ºC 4:34ºC 5:39ºC
6:40ºC (All temperatures are NORMAL.)
Rear Backplane: O.K.(rev.-04)
Temperature sensors (on rear backplane)
0:39ºC 1:45ºC 2:42ºC 3:39ºC 4:36ºC 5:37ºC
6:42ºC (All temperatures are NORMAL.)
Interconnect assembly
O.K.(rev.-02)
Loop configuration
Loop A is configured as a single loop.
Loop B is configured as a single loop.
Language USA English
#
Note the 3 disks displaying a 'Not Ready' message and the 1 disk displaying an 'Open Failed' message.
Any help/advice will be greatly appreciated.
Thanks!
Troy
# luxadm display ORLANDO
SENA
DISK STATUS
SLOT FRONT DISKS (Node WWN) REAR DISKS (Node WWN)
0 On (Not Ready) 2000002037337221 On (O.K.) 20000020372b5a14
1 On (O.K.) 20000020372b5594 On (O.K.) 20000020372b4e58
2 On (Not Ready) 200000203726fe15 On (O.K.) 20000020374fa786
3 On (O.K.) 20000020372b5079 On (Not Ready) 200000203733d4cf
4 On (O.K.) 20000020372b4d63 On (O.K.) 20000020372b4991
5 On (O.K.) 20000020372b4fa4 On (O.K.) 2000002037457705
6 On (Open Failed) 200000203722d50e On (O.K.) 200000203726ea2a
SUBSYSTEM STATUS
FW Revision:1.09 Box ID:0 Node WWN:5080020000049358 Enclosure Name:ORLAND
Power Supplies (0,2 in front, 1 in rear)
0 O.K.(rev.-02) 1 O.K.(rev.-02) 2 O.K.(rev.-02)
Fans (0 in front, 1 in rear)
0 O.K.(rev.-04) 1 O.K.(rev.-00)
ESI Interface board(IB) (A top, B bottom)
A: O.K.(rev.-04)
GBIC module (1 on left, 0 on right in IB)
0 O.K.(mod.-01)
1 Not Installed
B: O.K.(rev.-04)
GBIC module (1 on left, 0 on right in IB)
0 O.K.(mod.-01)
1 Not Installed
Disk backplane (0 in front, 1 in rear)
Front Backplane: O.K.(rev.-04)
Temperature sensors (on front backplane)
0:37ºC 1:37ºC 2:37ºC 3:37ºC 4:34ºC 5:39ºC
6:40ºC (All temperatures are NORMAL.)
Rear Backplane: O.K.(rev.-04)
Temperature sensors (on rear backplane)
0:39ºC 1:45ºC 2:42ºC 3:39ºC 4:36ºC 5:37ºC
6:42ºC (All temperatures are NORMAL.)
Interconnect assembly
O.K.(rev.-02)
Loop configuration
Loop A is configured as a single loop.
Loop B is configured as a single loop.
Language USA English
#
Note the 3 disks displaying a 'Not Ready' message and the 1 disk displaying an 'Open Failed' message.
Any help/advice will be greatly appreciated.
Thanks!
Troy