Hi
I am hoping someone can offer some advice as I am lost and not sure where to go next to solve this issue.
We have An IP 406 V1, not 100% certain it's a V1 but fairly certain it is. It has a VCM 5 installed and is at software level 3.0(40) and has 2 Analogue POTS 30's attached. We also have a remote system, a Cisco Call Manager Express.
What we have tried to do is create a VoIP link between the two sites by adding a VoIP line in the Avaya config and a short code to pick up calls to extensions on the remote system and route them down the VoIP line. The equivalent is done at the other end to route calls to the Avaya extensions down the VoIP line and all other calls as well so that all external calls break out of the Avaya.
When we put all this in it works fine and all the calls go where they are supposed to go. However the system just crashes and reboots about 4 or 5 times a day. The only way to stop it doing so is to remove the VoIP line entry.
I have had System Monitor running during a crash but the logs are largely meaningless to me. It doesn't look like it happens if there are too many VoIP calls operating, ie more than 5 at any one time. I have looked into upgrading the system but I am reluctant to as:
a) I have had bad experiences with upgrades in the past
b) There isn't enough memory for a version 4.0 upgrade
c) I have worked with systems in the past where this type of VoIP link has worked fine on 406's with the same s/w version
We have spoken to our Avaya supplier and they are less than helpful and done as much reading as from Avaya articles and forums as I can but don't seem to be getting very far.
I just wanted to know whether anyone had any ideas on:
a) Should this work with a version 3.(40) system or are there any known issues?
b) Are there any known issues linking Cisco Call Manager Expresses?
c) Is upgrading a 406 to Version 3.2 possible/problematic?
d) Any other suggestions on what may be the cause or things to try?
Any help gratefully received.
Chris
I am hoping someone can offer some advice as I am lost and not sure where to go next to solve this issue.
We have An IP 406 V1, not 100% certain it's a V1 but fairly certain it is. It has a VCM 5 installed and is at software level 3.0(40) and has 2 Analogue POTS 30's attached. We also have a remote system, a Cisco Call Manager Express.
What we have tried to do is create a VoIP link between the two sites by adding a VoIP line in the Avaya config and a short code to pick up calls to extensions on the remote system and route them down the VoIP line. The equivalent is done at the other end to route calls to the Avaya extensions down the VoIP line and all other calls as well so that all external calls break out of the Avaya.
When we put all this in it works fine and all the calls go where they are supposed to go. However the system just crashes and reboots about 4 or 5 times a day. The only way to stop it doing so is to remove the VoIP line entry.
I have had System Monitor running during a crash but the logs are largely meaningless to me. It doesn't look like it happens if there are too many VoIP calls operating, ie more than 5 at any one time. I have looked into upgrading the system but I am reluctant to as:
a) I have had bad experiences with upgrades in the past
b) There isn't enough memory for a version 4.0 upgrade
c) I have worked with systems in the past where this type of VoIP link has worked fine on 406's with the same s/w version
We have spoken to our Avaya supplier and they are less than helpful and done as much reading as from Avaya articles and forums as I can but don't seem to be getting very far.
I just wanted to know whether anyone had any ideas on:
a) Should this work with a version 3.(40) system or are there any known issues?
b) Are there any known issues linking Cisco Call Manager Expresses?
c) Is upgrading a 406 to Version 3.2 possible/problematic?
d) Any other suggestions on what may be the cause or things to try?
Any help gratefully received.
Chris