Hi All, I've been trying to get T1 config working but no luck. My command is not accepted from "Config t".
isdn switch-type primary-ni
^
% Invalid input detected at '^' marker.
Here is what I have on 2821:
sh inventory
NAME: "2821 chassis", DESCR: "2821 chassis"
PID: CISCO2821 , VID: V04 , SN: FHK1145F24R
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC11442V19
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSl
ot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 , SN: FOC13371WEA
NAME: "PVDMII DSP SIMM with three DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP
SIMM with three DSPs"
PID: PVDM2-48 , VID: V01 , SN: FOC11372FMC
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP S
IMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC110731WT
NAME: "AIM Service Engine 1", DESCR: "AIM Service Engine"
PID: AIM-CUE , VID: V03 , SN: FOC12260L73
Camoroz2821#
ip interface brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM up down
GigabitEthernet0/0.22 192.68.27.2 YES NVRAM up down
GigabitEthernet0/0.122 192.68.127.2 YES NVRAM up down
Service-Engine0/1 192.68.127.2 YES TFTP up up
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
Camoroz2821#
T1 will be used for voice traffic with bunch of DID only. This is my first time trying to get this work. Appreciate all your help and I have a dead line to make this working.
Please help.
Thanks in advance.
isdn switch-type primary-ni
^
% Invalid input detected at '^' marker.
Here is what I have on 2821:
sh inventory
NAME: "2821 chassis", DESCR: "2821 chassis"
PID: CISCO2821 , VID: V04 , SN: FHK1145F24R
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC11442V19
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSl
ot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 , SN: FOC13371WEA
NAME: "PVDMII DSP SIMM with three DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP
SIMM with three DSPs"
PID: PVDM2-48 , VID: V01 , SN: FOC11372FMC
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP S
IMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC110731WT
NAME: "AIM Service Engine 1", DESCR: "AIM Service Engine"
PID: AIM-CUE , VID: V03 , SN: FOC12260L73
Camoroz2821#
ip interface brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM up down
GigabitEthernet0/0.22 192.68.27.2 YES NVRAM up down
GigabitEthernet0/0.122 192.68.127.2 YES NVRAM up down
Service-Engine0/1 192.68.127.2 YES TFTP up up
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
Camoroz2821#
T1 will be used for voice traffic with bunch of DID only. This is my first time trying to get this work. Appreciate all your help and I have a dead line to make this working.
Please help.
Thanks in advance.