2620XM MPLS-BGP and nm-HDV2-1t1/e1 problem

[Robroy2003]

Guys, I need some help please. I was upgrading my routers this weekend to new MPLS circuits running BGP. My ios on the routers does not support BGP. I downloaded spservices and installed it, but it did not support the nm-hdv2 module in the routers going to the phone switch. I am going to catch alot of grief on Monday if I don't have this worked out. I have found that an older version of ip voice will work, but cannot find a copy of it. It has been pulled from Cisco's site. I need ip voice for a 2620XM version 12.3(2)T9 or earlier. Can anyone help me out here.

Thanks

 

[burtsbees]

How much DRAM/flash do you have?

Burt

 

[Robroy2003]

I have 32 Meg Flash and 96 Meg Dram.
Mark

 

[burtsbees]

Either this
ftp://69.150.40.77/Cisco%20Stuff/IOS%20files/c2600-jsx-mz.123-13.bin
or this...

ftp://69.150.40.77/Cisco%20Stuff/IOS%20files/c2600-advsecurityk9-mz.123-14.T7.bin
should work.

Burt

 

[Robroy2003]

Thanks Burt, Trying them now and I'll let you know how it goes.

Mark

 

[Robroy2003]

Well, neither one of those will support the nm-hdv2 card. After installing them and rebooting, I do a show diag and the card in that slot is unknown. More options would be greatly appreciated. If anyone has an older 2620xm ip voice package they could get to me, that would be great.

Thanks again
Mark Spencer

 

[burtsbees]

This is the only other one I have...

ftp://69.150.40.77/Cisco%20Stuff/IOS%20files/c2600-ik9o3s3-mz.123-15b.bin

Burt

 

[Robroy2003]

Well Burt, I appreciate the effort, but that one will not recognize the nm=hdv2 card either. Any other help out there would be greatly appreciated.

 

[plshlpme]

cisco says 12.3(t)T

Cisco IOS Software Support1
2600XM, 2691, 3725, 3745
2811, 2821, 2851
3825, 3845

NM-HDV2, NM-HDV2-1T1/E1, NM-HDV2-2T1/E1
12.3(7)T
12.3(8)T4
12.3(11)T

PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, PVDM2-64
12.3(7)T
12.3(8)T4
12.3(11)T

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a008039c333.shtml

was this working before you upgraded the ios?

what version did you have on it?

 

[Robroy2003]

I was running c2600-ipvoice-mz.123-8.T5.bin but it does not support BGP. c2600-ipvoice-mz.123-1 and up to 123.2T9 does support BGP but anything new than that does not. I just cannot find an old copy of the ipvoice software. If I upgrade to spservices or just about anything else, the nm-hdv2 module is not recognized. I have the routers running ipvoice 123-8.T5.bin now and the nm module works fine. I just cannot run BGP that my MPLS requires. If all else fails, I can have the MPLS Provider remove BGP and run EIGRP or something, but BGP is prefered.

Thanks again for all he help