DoomMaster
Programmer
First question is about the forums.
I had an account before called MrDoomMaster, but for some reason all my threads I made were removed and now when I try to log on I get the message "There has been a problem with your account registration. Contact Tek-Tips support to discuss the issue"
Why is it doing this? I emailed Tek Tips already, they aren't answering back.
Secondly, I'm working on an assembler program, and I can't seem to figure out why it isn't working.
The code consists of a loop, which is supposed to exit once CL becomes greater than the immediate value of E0H
Inside of the loop, the first instruction is to set the cursor to a column that doesn't change, and a row that increments by 1. This supports the automatic line switching to allow lines to be placed below each other.
After the cursor is moved one line below, then an instruction is given to display a name + an offset. This offset is also incremented by 20H (because that's the length of each string, check out the data segment. All strings are the same length, so each is 20H in space)
Try to run and compile this program, and see if you can get it to work. I honestly have tried everything, I can't get it to switch lines when I try to move the cursor. Also I seem to have run out of registers to store numbers in for the counters. bah so confusing, I'm so lost
I had an account before called MrDoomMaster, but for some reason all my threads I made were removed and now when I try to log on I get the message "There has been a problem with your account registration. Contact Tek-Tips support to discuss the issue"
Why is it doing this? I emailed Tek Tips already, they aren't answering back.
Secondly, I'm working on an assembler program, and I can't seem to figure out why it isn't working.
The code consists of a loop, which is supposed to exit once CL becomes greater than the immediate value of E0H
Inside of the loop, the first instruction is to set the cursor to a column that doesn't change, and a row that increments by 1. This supports the automatic line switching to allow lines to be placed below each other.
After the cursor is moved one line below, then an instruction is given to display a name + an offset. This offset is also incremented by 20H (because that's the length of each string, check out the data segment. All strings are the same length, so each is 20H in space)
Try to run and compile this program, and see if you can get it to work. I honestly have tried everything, I can't get it to switch lines when I try to move the cursor. Also I seem to have run out of registers to store numbers in for the counters. bah so confusing, I'm so lost
Code:
PAGE 60,132
TITLE L9RCD (EXE) LAB 9
;------------------------------------------------
;--------TABS-SHOULD-BE-SET-TO-4-SPACES----------
;------------------------------------------------
STACK SEGMENT PARA STACK 'Stack'
DW 32 DUP (0)
STACK ENDS
;------------------------------------------------
DATASEG SEGMENT PARA 'Data'
S0 DB '*** *** *** **** *** *****$'
S1 DB '* * * * * * * * * * $'
S2 DB '*** * * *** *** *** * $'
S3 DB '* * * * * * * * * * $'
S4 DB '* * *** *** **** * * * $'
S5 DB '*** ** ***** * **** * *$'
S6 DB '* * * * * * * * * $'
S7 DB '* * **** * * *** * $'
S8 DB '* * * * * * * * $'
S9 DB '*** * * ***** **** **** * $'
DATASEG ENDS
;------------------------------------------------
;------------------------------------------------
CODESEG SEGMENT PARA 'Code'
MAIN PROC FAR
ASSUME SS:STACK,DS:DATASEG,CS:CODESEG
MOV AX,DATASEG
MOV DS,AX
MOV AX,0600H
MOV BH,14H
MOV CX,0000H
MOV DX,184FH
INT 10H ;SCROLL SCREEN::F=RED:B=BLUE
;MOV DH,8 ;SET ROW COUNTER
MOV CL,00H ;SET LOOP COUNTER
DLOOP: MOV AH,02H
MOV BH,00H
MOV DH,10 ;INCREMENT ROW COUNTER
MOV DL,14
INT 10H ;SET CURSOR
MOV AH,09H
LEA DX,[S0]
INT 21H ;DISPLAY DATALINE
ADD CL,20H ;INCREMENT DATALINE COUNTER
CMP CX,00E0H
JAE DLOOP ;LOOP TO PRINT NEXT DATALINE
MOV AX,4C00H
INT 21H
MAIN ENDP
CODESEG ENDS
END MAIN
;------------------------------------------------
;------------------------------------------------
ATASEG,CS:CODESEG